Nissan Tiida C11. Instruction — part 293
DLK-582
< ON-VEHICLE MAINTENANCE >
[WITHOUT I-KEY & SUPER LOCK]
PRE-INSPECTION FOR DIAGNOSTIC
ON-VEHICLE MAINTENANCE
PRE-INSPECTION FOR DIAGNOSTIC
Basic Inspection
INFOID:0000000001397122
BASIC INSPECTION
1.
CHECK DOOR LOCK AND UNLOCK SWITCH OPERATION
Check door lock and unlock operation by operating door lock and unlock switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
DLK-567, "DOOR LOCK AND UNLOCK SWITCH : Symptom Table"
.
2.
CHECK KEYFOB OPERATION
Check door lock and unlock operation by operationg lock and unlock button of keyfob.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Refer to
DLK-567, "KEYFOB : Symptom Table"
.
3.
CHECK AUTO DOOR LOCK OPERATION
Check auto door lock operation. Refer to
XX-XX, "*****"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Refer to
XX-XX, "*****"
.
4.
CHECK VEHICLE SPEED SENSING AUTO DOOR LOCK OPERATION
Check vehicle speed sensing auto door lock. Refer to
XX-XX, "*****"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Refer to
XX-XX, "*****"
.
5.
CHECK BACK DOOR OPENER SWITCH OPERATION
Check back door opener operation by operating back door opener switch.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Refer to
DLK-569, "BACK DOOR OPENER SWITCH : Symptom Table"
6.
CHECK HAZARD REMINDER FUNCTION
Check hazard reminder function by operating the following switches.
• Lock and unlock button of keyfob.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Refer to
DLK-572, "HAZARD WARNING LAMP : Symptom Table"
7.
CHECK WARNING FUNCTION
Check that warning function operate properly. Refer to
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Refer to
DLK-571, "BACK DOOR : Symptom Table"
8.
CHECK OUT
CHECK OUT.
>> INSPECTION END
HOOD
DLK-583
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL AND INSTALLATION
HOOD
Fitting Adjustment
INFOID:0000000001732035
FRONT END HEIGHT ADJUSTMENT AND LATERAL/LONGITUDINAL CLEARANCE ADJUST-
MENT
1.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2.
Remove hood lock. Rotate bumper rubber to adjust height until
hood becomes 1.0 to 1.5 mm lower than the fender.
3.
Position hood lock and engage striker. Check hood lock and
striker for looseness. Tighten lock bolts to the specified torque.
4.
Install the front grille. Refer to
EXT-19, "Removal and Installa-
CAUTION:
Adjust the clearance between hood and other parts so that the
dimensional difference left and right is as follows.
SURFACE MISMATCH ADJUSTMENT
1.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2.
Release hood lock, and adjust surface level difference of hood, fender, and headlamp according to the fit-
ting standard dimension, using RH and LH bumper rubbers.
3.
Install and align the hood lock until the center of the striker and the hood lock are vertically aligned.
PIIB6508E
Hood and headlamp (B - B)
: Less than 2.0 mm (0.08 in)
Hood and fender (C - C)
: Less than 1.5 mm (0.06 in)
Hood and fender (D - D)
: Less than 1.5 mm (0.06 in)
PIIB2526J
Hood and front bumper (A - A)
: -1.3 - 2.7 mm (-0.05 - 0.11 in)
Hood and fender (D - D)
: -0.4 - 1.7 mm (-0.16 - 0.07 in)
DLK-584
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY & SUPER LOCK]
HOOD
4.
Press the hood lightly with [approx. 29 N (3 kg] of force and adjust A and B as shown.
5.
After adjustment tighten lock bolts to the specified torque.
6.
Install the front grille. Refer to
EXT-19, "Removal and Installation"
.
Removal and Installation
INFOID:0000000001732036
HOOD ASSEMBLY
Removal
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A
: 20 mm (0.79 in)
B
: 6.8 mm (0.268 in) min.
PIIB5794E
1.
Hood hinge
2.
Hood stay
3.
Radiator core seal rubber
4.
Hood assembly
5.
Hood insulator
6.
Hood stay holder
PIIB2528J
HOOD
DLK-585
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Remove hinge nuts on hood and remove hood assembly.
CAUTION:
Two technicians should be used to avoid damaging the
hood during removal.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Before installing hood hinge, apply anticorrosive agent onto the surfaces that make contact with the
vehicle body.
• After installing, perform hood fitting adjustment. Refer to
.
HOOD HINGE
Removal
1.
Remove hood assembly. Refer to
DLK-584, "Removal and Installation"
2.
Remove front fender. Refer to
DLK-591, "Removal and Installation"
3.
Remove bolts and the hood hinge.
Installation
Installation is in the reverse order of removal.
Removal and Installation of Hood Lock Control
INFOID:0000000001732037
LH Drive
12.7 N·m (1.3 kg-m, 9.4 ft-lb)
PIIB2529J
12.7 N·m (1.3 kg-m, 9.4 ft-lb)
PIIB2530J
PIIB6509E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст