Nissan Tiida C11. Instruction — part 1369
DISASSEMBLY
TM-527
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
41. Remove overrun clutch hub (1) from forward clutch drum.
42. Remove thrust washer (1) from overrun clutch hub (2).
• Inspect thrust washer (1) and overrun clutch hub (2), and
replace if damaged or worn.
43. Remove forward clutch assembly and overrun clutch assembly
(1) from transaxle case.
44. Remove needle bearing (1) and thrust washer (2) from bearing
retainer.
• Inspect needle bearing (1) and thrust washer (2), and
replace damaged or worn.
45. Remove side cover fitting bolts (1), and then remove side cover
by lightly tapping it using a soft hammer.
CAUTION:
Do not damage side cover.
46. Remove side cover gasket from side cover.
SCIA5898J
SCIA5899J
SCIA5900J
SCIA5901J
SCIA6039J
TM-528
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
DISASSEMBLY
47. Remove output shaft, output gear and reduction gear according to the following procedures.
a.
Set instruction shaft in “P” position to fix idler gear and output gear.
b.
Unlock both idler gear and output gear lock nuts using a pin punch.
c.
Remove idler gear and output gear lock nuts.
d.
Remove idler gear (2) and output gear (1) using Tool A.
e.
Remove reduction pinion gear and output shaft from transaxle
case.
f.
Remove reduction pinion gear adjusting shim (1) from reduction
pinion gear (2).
g.
Remove output gear adjusting spacer (3) from output shaft (4).
48. Remove bearing retainer fitting bolts, and then remove bearing
retainer (1) from transaxle case.
SAT704D
Tool number:
ST27180001
SCIA6991E
SCIA5902J
SCIA5909J
DISASSEMBLY
TM-529
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
49. Remove return spring (2) from parking shaft (3) suitable tool.
(1): Parking pawl
• Inspect return spring (2), and replace if damaged or worn.
50. Draw out parking shaft (1), and then remove parking pawl (2)
from transaxle case.
• Inspect parking shaft (1) and parking pawl (2), and replace
if damaged or worn.
51. Remove parking actuator support (1) from transaxle case.
• Inspect parking actuator support (1), and replace if dam-
aged or worn.
52. Remove snap ring from transaxle case using suitable tool.
53. Remove governor cap from transaxle case.
54. Remove O-ring from governor cap.
55. Remove LH differential side oil seal from transaxle case using
suitable tool.
CAUTION:
Do not scratch transaxle case.
SCIA6996E
SCIA6997E
SCIA6998E
ATM0076D
TM-530
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
REPAIR FOR COMPONENT PARTS
Instruction Shaft
INFOID:0000000001731435
COMPONENTS
REMOVAL
1.
Remove detent spring from transaxle case.
2.
Drive out retaining pin of instruction plate using suitable tool.
1.
Instruction shaft oil seal
2.
Parking rod
3.
Retaining pin
4.
Parking rod plate
5.
Retaining pin
6.
Instruction plate
7.
Instruction shaft
8.
Detent spring
9.
Retaining pin
SCIA5907J
SAT313G
SAT076D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст