Nissan Tiida C11. Instruction — part 757
EXL-26
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000001528970
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
BCM
BCM : CONSULT-III Function (BCM - BCM)
INFOID:0000000001528971
WORK SUPPORT
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000001528977
WORK SUPPORT
*: Initial setting
DATA MONITOR
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM. Refer to
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION
The BCM part number is displayed.
CONFIGURATION
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
Item
Description
RESET SETTING VALUE
Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
Work item
Setting
Description
BATTERY SAVER SET
ON*
Battery saver mode can be changed.
OFF
Monitor item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
HI BEAM SW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
H/L SW POS [ON/OFF]
LIGHT SW 1ST [ON/OFF]
PASSING SW [ON/OFF]
AUTO LIGHT SW [ON/OFF]
FR FOG SW [ON/OFF]
RR FOG SW [ON/OFF]
DOOR SW-DR [ON/OFF]
The switch status input from front door switch (driver side)
ENGINE STATUS
The engine status received from ECM with CAN communication
DIAGNOSIS SYSTEM (BCM)
EXL-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000001528979
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
LIT-SEN FAIL [OK/NOTOK]
• The sensor status received from light & rain sensor with serial link
• The serial link condition that BCM judges
AUT LIGHT SYS [ON/OFF]
Auto light system status that BCM judges from the vehicle condition
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF
Stops the front fog lights request signal transmission.
RR FOG LAMP
ON
• Outputs the voltage to turn the rear fog lamp ON.
• Transmits the rear fog lamp status signal to the combination meter with
CAN communication to turn the rear fog lamp indicator lamp ON.
OFF
• Stops the voltage to turn the rear fog lamp OFF.
• Stops the rear fog lamp status signal transmission.
DAYTIME RUNNING LIGHT
ON
Transmits the day time running light request signal to IPDM E/R with
CAN communication to turn the each lamps ON.
OFF
Stops the day time running light request signal transmission.
Work Item
Description
HAZARD LAMP SET
Operation
MODE1
MODE2
MODE3
MODE4
Keyfob operation
Lock
Unlock
Lock
Unlock
Lock
Unlock
Lock
Unlock
Hazard lamp flash
-
-
-
Twice
Once
-
Once
Twice
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF]
The switch status input from the hazard switch
TURN SIGNAL R [ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
TURN/L MNTR [ON/OFF]
Displays status (one bulb out: ON/other: OFF) as judged from bulb signal
EXL-28
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)
INFOID:0000000001528982
DATA MONITOR
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000001528984
WORK SUPPORT
Test Item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON.
LH
Outputs the voltage to turn the left side turn signal lamps ON.
OFF
Stops the voltage to turn the turn signal lamps OFF.
Monitor Item
[Unit]
Description
TURN SIGNAL R
[OFF/ON]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.
TURN SIGNAL L
[OFF/ON]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.
HI BEAM SW
[OFF/ON]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.
H/L SW POS
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function.
LIGHT SW 1ST
[OFF/ON]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function.
PASSING SW
[OFF/ON]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.
AUTO LIGHT SW
[OFF/ON]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.
FR FOG SW
[OFF/ON]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.
RR FOG SW
[OFF/ON]
Displays the status of the RR FOG switch in combination switch judged by BCM with the combination switch
reading function.
FR WIPER HI
[OFF/ON]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER LOW
[OFF/ON]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER INT
[OFF/ON]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
FR WASHER SW
[OFF/ON]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
INT VOLUME
[1 - 7]
Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
function.
RR WIPER ON
[OFF/ON]
Displays the status of the RR WIPER switch in combination switch judged by BCM with the combination
switch reading function.
RR WIPER INT
[OFF/ON]
Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
RR WASHER SW
[OFF/ON]
Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
DIAGNOSIS SYSTEM (BCM)
EXL-29
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*: Initial setting
DATA MONITOR
1: With remote keyless entry
2: With Intelligent Key
ACTIVE TEST
*: Each lamp switch is in ON position.
Work Item
Setting Item
Setting
ROOM LAMP TIMER SET
MODE 1*
15 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
30 min.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judges from IGN signal (ignition power supply)
KEY SW
1
[ON/OFF]
The switch status input from key switch
PUSH SW
2
[ON/OFF]
Push switch status received from Intelligent Key unit by CAN communication
DOOR SW-DR [ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS [ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR [ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL [ON/OFF]
The switch status input from rear door switch LH
BACK DOOR SW [ON/OFF]
The switch status input from back door switch
CDL LOCK SW [ON/OFF]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW [ON/OFF]
Unlock switch status input from door lock and unlock switch
I-KEY LOCK
2
[ON/OFF]
Lock signal status received from Intelligent Key unit by CAN communication
I-KEY UNLOCK
2
[ON/OFF]
Unlock signal status received from Intelligent Key unit by CAN communication
KEYLESS LOCK
1
[ON/OFF]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
KEYLESS UNLOCK
1
[ON/OFF]
Unlock signal status received from remote keyless entry receiver (integrated in the
BCM)
Test item
Operation
Description
BATTERY SAVER
OFF
Cuts the interior room lamp power supply to turn interior room lamps OFF.
ON
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст