Nissan Tiida C11. Instruction — part 357
EC-78
< FUNCTION DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
EVAPORATIVE EMISSION SYSTEM
EVAPORATIVE EMISSION SYSTEM
System Diagram
INFOID:0000000001161163
EVAPORATIVE EMISSION LINE DRAWING
PBIB3039E
EVAPORATIVE EMISSION SYSTEM
EC-79
< FUNCTION DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1.
Intake manifold collector
2.
EVAP canister purge volume con-
trol solenoid valve
3.
EVAP purge resonator
:
Vehicle front
:
From next figure
PBIB2946E
EC-80
< FUNCTION DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
EVAPORATIVE EMISSION SYSTEM
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
System Description
INFOID:0000000001161164
INPUT/OUTPUT SIGNAL CHART
*1: ECM determines the start signal status by the signals of engine speed and battery voltage.
*2: This signal is sent to the ECM through CAN communication line.
SYSTEM DESCRIPTION
The evaporative emission system is used to reduce hydrocarbons emitted into the atmosphere from the fuel
system. This reduction of hydrocarbons is accomplished by activated charcoals in the EVAP canister.
The fuel vapor in the sealed fuel tank is led into the EVAP canister which contains activated carbon and the
vapor is stored there when the engine is not operating or when refueling to the fuel tank.
1.
EVAP canister
:
Vehicle front
:
To previous figure
ALBIA0274ZZ
Sensor
Input signal to ECM
ECM function
Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*
1
EVAP canister
purge flow control
EVAP canister purge vol-
ume control solenoid valve
Mass air flow sensor
Amount of intake air
Engine coolant temperature sensor
Engine coolant temperature
Battery
Battery voltage*
1
Throttle position sensor
Throttle position
Accelerator pedal position sensor
Accelerator pedal position
Heated oxygen sensor 1
Density of oxygen in exhaust gas
(Mixture ratio feedback signal)
Combination meter
Vehicle speed*
2
EVAPORATIVE EMISSION SYSTEM
EC-81
< FUNCTION DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
The vapor in the EVAP canister is purged by the air through the purge line to the intake manifold when the
engine is operating. EVAP canister purge volume control solenoid valve is controlled by ECM. When the
engine operates, the flow rate of vapor controlled by EVAP canister purge volume control solenoid valve is
proportionally regulated as the air flow increases.
EVAP canister purge volume control solenoid valve also shuts off the vapor purge line during decelerating.
Component Parts Location
INFOID:0000000001677957
1.
Ignition coil (with power transistor)
and spark plug
2.
Intake valve timing control solenoid
valve
3.
Refrigerant pressure sensor
4.
Knock sensor
5.
Fuel injector
6.
Cooling fan motor
7.
Camshaft position sensor (PHASE)
8.
IPDM E/R
9.
ECM
10. Mass air flow sensor (with intake air
temperature sensor)
11.
Engine coolant temperature sensor
12. Electric throttle control actuator
(with built in throttle position sensor
and throttle control motor)
13. EVAP canister purge volume control
solenoid valve
PBIB2939E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст