Nissan Tiida C11. Instruction — part 1331
TORQUE CONVERTER CLUTCH SOLENOID VALVE
TM-375
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
CHECK VALVE RESISTANCE
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly connector in engine room.
3.
Check resistance between terminal cord assembly harness con-
nector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
5.
CHECK DTC
Perform
TM-373, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
XX-XX, "*****"
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Component Inspection
INFOID:0000000001713033
TORQUE CONVERTER CLUTCH SOLENOID VALVE
• For removal, refer to
XX-XX, "*****"
.
Resistance Check
• Check resistance between terminal and ground.
Operation Check
• Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal and ground.
Solenoid valve
Connector
Terminal
Resistance (Approx.)
Torque converter clutch
solenoid valve
F30
5 - Ground
5 - 20
Ω
SCIA4946E
Solenoid valve
Terminal
Resistance (Ap-
prox.)
Torque converter
clutch solenoid
valve
5
Ground
5 - 20
Ω
SCIA2063E
SCIA2066E
TM-376
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM POW-
ER SOURCE)
BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)
Description
INFOID:0000000001713034
The A/T fluid temperature sensor detects the A/T fluid temperature and sends the signal to the TCM.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000001713035
Remarks: Specification data are reference values.
On Board Diagnosis Logic
INFOID:0000000001713036
Diagnostic trouble code “BATT/FLUID TEMP SEN” with CONSULT-III or 8th judgement flicker without CON-
SULT-III is detected when TCM receives an excessively low or high voltage from the sensor.
Possible Cause
INFOID:0000000001713037
• Harness or connector
(Sensor circuit is open or shorted.)
• A/T fluid temperature sensor
DTC Confirmation Procedure
INFOID:0000000001713038
CAUTION:
• Always drive vehicle at a safe speed.
• If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1.
Start engine.
2.
Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3.
Touch “START”.
4.
Drive vehicle under the following conditions.
SLCT LVR POSI: “D” position
VEHICLE SPEED: Higher than 20 km/h (12 MPH)
5.
If the check result is NG, go to
WITHOUT CONSULT-III
1.
Start engine.
2.
Drive vehicle under the following conditions.
Selector lever position: “D” position
Vehicle speed: Higher than 20 km/h (12 MPH)
3.
Perform self-diagnosis. Refer to
TM-350, "Diagnosis Procedure without CONSULT-III"
4.
If the check result is NG, go to
Diagnosis Procedure
INFOID:0000000001713040
1.
CHECK TCM POWER SOURCE
1.
Turn ignition switch ON. (Do not start engine.)
Item name
Condition
Display value (Approx.)
FLUID TEMP SE
When A/T fluid temperature is 20
°
C (68
°
F).
1.5V
When A/T fluid temperature is 80
°
C (176
°
F).
0.5V
BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM POW-
ER SOURCE)
TM-377
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Check voltage between TCM connector terminal and ground.
3.
Turn ignition switch OFF.
4.
Check voltage between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness for short or open between ignition switch and TCM terminals 10, 19
• Harness for short or open between battery and TCM terminal 28
• 10A fuse (No.13, located in the fuse block) and 10A fuse (No.49, located in the IPDM E/R)
• Ignition switch.
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
3.
CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR
With CONSULT-III
1.
Start engine.
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3.
Read out the value of “FLUID TEMP SE”.
Without CONSULT-III
1.
Start engine.
Item
Connector
Terminal
Judgement standard (Ap-
prox.)
Power supply
E31
10
Battery voltage
19
Battery voltage
Power supply
(memory back-up)
E32
28
Battery voltage
SCIA2656E
Item
Connector
Terminal
Judgement standard (Approx.)
Power supply
E31
10
0V
19
0V
Power supply
(memory back-up)
E32
28
Battery voltage
SCIA2657E
Item name
Condition
Display value
(Approx.)
FLUID TEMP
SE
When A/T fluid temperature is 20
°
C (68
°
F).
1.5V
When A/T fluid temperature is 80
°
C (176
°
F).
0.5V
TM-378
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM POW-
ER SOURCE)
2.
Check voltage TCM connector terminals while warming up A/T.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness for short or open between TCM, ECM and terminal cord assembly
• Ground circuit for ECM.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
5.
CHECK FLUID TEMPERATURE SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the TCM connector.
3.
Check resistance between TCM connector terminals.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 6.
6.
CHECK HARNESS BETWEEN TCM AND TERMINAL CORD ASSEMBLY HARNESS CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly harness connector and TCM connector.
3.
Check continuity between terminal cord assembly harness con-
nector terminals and TCM connector terminals.
4.
If OK, check harness for short to ground and short to power.
5.
If OK, check continuity between ground and transaxle assembly.
6.
Reinstall any part removed.
OK or NG
OK
>> GO TO 7.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
Item
Connector
Terminal
Condition
Judgement
standard
(Approx.)
A/T fluid
temperature
sensor
E32
47 - 42
When A/T fluid tempera-
ture is 20
°
C (68
°
F).
1.5V
When A/T fluid tempera-
ture is 80
°
C (176
°
F).
0.5V
SCIA2658E
Item
Connector
Terminal
Tempera-
ture
°
C (
°
F)
Resistance
(Approx.)
A/T fluid
temperature
sensor
E32
47 - 42
20 (68)
2.5 k
Ω
80 (176)
0.3 k
Ω
SCIA4947E
Item
Connector
Terminal
Continuity
TCM
E32
42
Yes
Terminal cord assembly
harness connector
F30
7
TCM
E32
47
Yes
Terminal cord assembly
harness connector
F30
6
SCIA2660E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст