Nissan Tiida C11. Instruction — part 39
BCS-20
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000001451470
WORK SUPPORT
*: Initial setting
DATA MONITOR
Work Item
Description
HAZARD LAMP SET
Answer back function (hazard) mode can be changed in this mode.
For the detail of the setting, refer to
DLK-617, "REMOTE KEYLESS ENTRY : System Descrip-
.
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 2 minutes
• MODE 3: 3 minutes
• MODE 4: 4 minutes
• MODE 5: 5 minutes
Monitor Item
[Unit}
Condition
IGN ON SW [ON/OFF]
Indicates condition of ignition switch in ON position.
KEY SW [ON/OFF]
Indicates condition of key switch.
KEYLESS LOCK [ON/OFF]
Indicates condition of lock signal from keyfob.
KEYLESS UNLOCK [ON/OFF]
Indicates condition of unlock signal from keyfob.
DOOR SW-DR [ON/OFF]
Indicates condition of front door switch (driver side).
DOOR SW-AS [ON/OFF]
Indicates condition of front door switch (passenger side).
DOOR SW-RR [ON/OFF]
Indicates condition of rear door switch RH.
DOOR SW-RL [ON/OFF]
Indicates condition of rear door switch LH.
BACK DOOR SW [ON/OFF]
Indicates condition of back door switch.
CDL LOCK SW [ON/OFF]
Indicates condition of door lock and unlock switch.
CDL UNLOCK SW [ON/OFF]
Indicates condition of door lock and unlock switch.
RKE LOCK AND UNLOCK
This item is indicated, but not monitored.
Test Item
Description
DOOR LOCK
This test is able to check warning chime in combination meter operation. [ALL LOCK/ALL UN-
LOCK/DR UNLOCK/OTHER UNLOCK]
INT LAMP
This test is able to check interior lamp operation [ON/OFF].
FLASHER
This test is able to check flasher operation [LH/RH/OFF].
Work item
Setting
Description
BATTERY SAVER SET
ON*
Battery saver mode can be changed.
OFF
Monitor item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
INFOID:0000000001451471
WORK SUPPORT
HI BEAM SW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
H/L SW POS [ON/OFF]
LIGHT SW 1ST [ON/OFF]
PASSING SW [ON/OFF]
AUTO LIGHT SW [ON/OFF]
FR FOG SW [ON/OFF]
RR FOG SW [ON/OFF]
DOOR SW-DR [ON/OFF]
The switch status input from front door switch (driver side)
ENGINE STATUS
The engine status received from ECM with CAN communication
LIT-SEN FAIL [OK/NOTOK]
• The sensor status received from light & rain sensor with serial link
• The serial link condition that BCM judges
AUT LIGHT SYS [ON/OFF]
Auto light system status that BCM judges from the vehicle condition
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF
Stops the front fog lights request signal transmission.
RR FOG LAMP
ON
• Outputs the voltage to turn the rear fog lamp ON.
• Transmits the rear fog lamp status signal to the combination meter with
CAN communication to turn the rear fog lamp indicator lamp ON.
OFF
• Stops the voltage to turn the rear fog lamp OFF.
• Stops the rear fog lamp status signal transmission.
DAYTIME RUNNING LIGHT
ON
Transmits the day time running light request signal to IPDM E/R with
CAN communication to turn the each lamps ON.
OFF
Stops the day time running light request signal transmission.
Work Item
Setting
Item
Description
WIPER SPEED
SETTING
ON
1
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
OFF
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
RR WIP RVRS
SET
ON
2
Change ON/OFF mode setting or rear wiper operation when gear is shifted to reverse
OFF
BCS-22
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
1: Factory setting
2: If equipped
DATA MONITOR
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000001451472
WORK SUPPORT
DATA MONITOR
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch ON status judged from ignition power supply.
FR WIPER HI [ON/OFF]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER LOW [ON/OFF]
FR WIPER INT [ON/OFF]
FR WASHER SW [ON/OFF]
INT VOLUME [1 - 7]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER STOP [ON/OFF]
Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
tion.
VEHICLE SPEED [km/h]
The value of the vehicle speed signal received from combination meter with CAN com-
munication.
H/L SW POS [ON/OFF]
RR WIPER ON [ON/OFF]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER INT [ON/OFF]
RR WASHER SW [ON/OFF]
RR WIPER STOP [ON/OFF]
Rear wiper motor (stop position) status input from the rear wiper motor.
REVERSE SW CAN [ON/OFF]
Transmission reverse position moitored via CAN.
Test Item
Operation
Description
HEADLAMP WASH-
ER
ON
Transmits the headlamp washer request signal to IPDM E/R with CAN communication to
operate the headlamp washer operation.
FR WIPER
HI
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LO
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
ON
Outputs the voltage to operate the rear wiper motor.
OFF
Stops the voltage to stop.
Work Item
Description
HAZARD LAMP SET
Operation
MODE1
MODE2
MODE3
MODE4
Keyfob operation
Lock
Unlock
Lock
Unlock
Lock
Unlock
Lock
Unlock
Hazard lamp flash
-
-
-
Twice
Once
-
Once
Twice
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT-III Function (BCM - AUTO AIR CONDITIONER)
INFOID:0000000001451473
ACTIVE TEST
DATA MONITOR
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000001451474
DATA MONITOR
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF]
The switch status input from the hazard switch
TURN SIGNAL R [ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
TURN/L MNTR [ON/OFF]
Displays status (one bulb out: ON/other: OFF) as judged from bulb signal
Test Item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON.
LH
Outputs the voltage to turn the left side turn signal lamps ON.
OFF
Stops the voltage to turn the turn signal lamps OFF.
Test Item
Operation
Description
A?C INDICATOR
ON
Outputs the signal to turn the A/C indicator ON.
OFF
Stops the signal to turn the A/C indicator OFF.
Monitor Item
[Unit]
Contents
IGNSW [ON/OFF]
Display [ignition switch position (On)/(Off), ACC position (Off)] status as judged form ignition
switch signal.
FAN ON SIG [ON/OFF]
Display [FAN (On)/FAN (Off)] status as judged form blower fan motor switch signal.
AIR COND SW [ON/OFF]
Display [COMP (On)/COMP (Off)] status as judged form air conditioner switch signal.
Monitor Item
[Unit]
Condition
IGN ON SW [ON/OFF]
Indicates condition of ignition switch in ON position.
PUSH SW [ON/OFF]
Indicates condition of ignition knob switch.
I-KEY LOCK [ON/OFF]
Indicates condition of lock signal from Intelligent Key.
I-KEY UNLOCK [ON/OFF]
Indicates [condition of unlock signal from Intelligent Key.
I-KEY ALL UNL [ON/OFF]
Indicates condition of all unlock signal from Intelligent Key.
I-KEY TRUNK OP [ON/OFF]
Indicates condition of trunk open signal from Intelligent Key.
DOOR SW-DR [ON/OFF]
Indicates condition of front door switch (driver side).
DOOR SW-AS [ON/OFF]
Indicates condition of front door switch (passenger side).
DOOR SW-RR [ON/OFF]
Indicates condition of rear door switch RH.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст