Nissan Tiida C11. Instruction — part 468
EC-522
< COMPONENT DIAGNOSIS >
[HR16DE (WITHOUT EURO-OBD)]
P0340 CMP SENSOR (PHASE)
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK CAMSHAFT POSITION SENSOR (PHASE)
EC-522, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace camshaft position sensor (PHASE).
7.
CHECK CAMSHAFT (INT)
Check the following.
• Accumulation of debris to the signal plate of camshaft (1) rear end
• Chipping signal plate of camshaft rear end
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft.
8.
CHECK INTERMITTENT INCIDENT
GI-55, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000001693302
1.
CHECK CAMSHAFT POSITION SENSOR (PHASE)-I
1.
Turn ignition switch OFF.
2.
Loosen the fixing bolt of the sensor.
3.
Disconnect camshaft position sensor (PHASE) harness connector.
4.
Remove the sensor.
5.
Visually check the sensor for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace camshaft position sensor (PHASE).
2.
CHECK CAMSHAFT POSITION SENSOR (PHASE)-II
Check resistance camshaft position sensor (PHASE) terminals as follows.
CMP sensor (PHASE)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
3
F11
65
Existed
PBIA9557J
PBIA9876J
P0340 CMP SENSOR (PHASE)
EC-523
< COMPONENT DIAGNOSIS >
[HR16DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace camshaft position sensor (PHASE).
Terminals (Polarity)
Resistance [at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0 or
∞
Ω
1 (+) - 3 (-)
2 (+) - 3 (-)
EC-524
< COMPONENT DIAGNOSIS >
[HR16DE (WITHOUT EURO-OBD)]
P0605 ECM
P0605 ECM
Description
INFOID:0000000001693314
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
DTC Logic
INFOID:0000000001693315
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1.
Turn ignition switch ON.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1.
Wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Repeat step 2 for 32 times.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
A)
ECM calculation function is malfunctioning.
• ECM
B)
ECM EEP-ROM system is malfunctioning.
C)
ECM self shut-off function is malfunctioning.
P0605 ECM
EC-525
< COMPONENT DIAGNOSIS >
[HR16DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Diagnosis Procedure
INFOID:0000000001693316
1.
INSPECTION START
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “SELF-DIAG RESULTS” mode with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE.
See
.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Erase the Diagnostic Test Mode II (Self-diagnostic results) memory.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
.
Is the 1st trip DTC P0605 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
EC-388, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
.
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст