Nissan Tiida C11. Instruction — part 793
FUEL TANK
FL-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
6.
Disconnect EVAP tube (2) at rear side of fuel tank.
• Vent hose (1)
•
⇐
: Vehicle front
7.
Remove fuel filler hose (3) at fuel filler tube side.
8.
If necessary, remove mounting screw and quick connectors and
slide the EVAP canister rearward to remove it from the fuel tank.
9.
Support center of fuel tank (1) with transmission jack (A).
10. Remove fuel tank straps (RH and LH).
11. Lower transmission jack carefully to remove fuel tank while sup-
porting it by hand.
CAUTION:
Fuel tank may be in an unstable position because of the
shape of fuel tank bottom. Be sure to support tank securely.
INSTALLATION
Note the following, and install in the reverse order of removal.
Fuel Filler Hose
• Install fuel filler hose to fuel tank, paying attention to install
mark.Marking faces downward
JPBIA0456ZZ
MBIB9040E
PBIC3792E
MBIB9043E
FL-12
< ON-VEHICLE REPAIR >
FUEL TANK
• Install fuel filler hose (2) to fuel filler tube (1), paying attention to
install mark. Marking faces rightward.
• Insert filler hose to the length below.
• When installing clamp, do not allow clamp to contact the bulge
(bump) part of the tube.
• Tighten the clamp of filler hose so that the remaining length of the
screw becomes the following.
EVAP Hose
1.
Check connections for damage or foreign material.
2.
Align the matching side connection part with the center of shaft,
and insert connector straight until it clicks.
3.
After connecting, pull out quick connector and centralized under-
floor piping by hand. Make sure connections are secure.
Installation of Fuel Tank Mounting Strap
• Install them in the proper position by referring to the identification stamp mark “R” and “L1” on the end.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1.
Turn ignition switch “ON” (without starting the engine), to check the connections for fuel leaks with the
electric fuel pump applying pressure to the fuel piping.
2.
Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.
: 35mm (1.38 in)
: 5 - 9mm (0.20 - 0.35 in)
MBIB9043E
PBIC1653E
FUEL TANK
FL-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
K9K
INFOID:0000000001723031
Exploded View
INFOID:0000000001723037
Removal and Installation
INFOID:0000000001722981
REMOVAL
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
1.
Remove RH rear wheel.
2.
Remove fuel level sensor unit. Refer to
FL-8, "Removal and Installation"
CAUTION:
• If fuel tank bottom face is not level, and remaining fuel level is high, tank position becomes
unstable, causing a danger. Drain fuel further than that in step 1 of the referenced procedure
until tank can be held by hand even if the balance is lost..
3.
Remove muffler. Refer to
EX-14, "Removal and Installation"
4.
Remove vehicle side insulator on upper center muffler and main muffler..
5.
Move parking brake cable from the lower face of fuel tank. Then remove clips for parking brake cable. .
1.
Fuel filler tube protector
2.
Fuel filler cap
3.
Fuel filler cap protector
4.
Fuel filler tube
5.
Hose clamp
6.
Fuel filler hose
7.
Hose clamp
8.
Fuel tank
9.
Fuel tank mounting straps
10. Fuel tank shield
11. Vent hose
E1BIA0014GB
FL-14
< ON-VEHICLE REPAIR >
FUEL TANK
6.
Disconnect fuel filler hose on fuel tank side.
CAUTION:
• If fuel tank bottom face is not level, and remaining fuel
level is high, tank position becomes unstable, causing a
danger. Drain fuel further than that in step 1 of the refer-
enced procedure until tank can be held by hand even if
the balance is lost..
7.
Remove vent hose at RH rear wheelwell side.
8.
Remove EVAP hose at front side of fuel tank.
• Disconnect the quick connector using the following procedure.
- Pinch quick connector square-parts with your fingers, and pull out
the quick connector by hand.
- If quick connector and tube on vehicle are stuck, push and pull
several times until they move, and pull out..
CAUTION:
• The tube can be removed when the tabs are completely
depressed. Do not twist it more than necessary.
• Do not use any tools to remove the quick connector.
• Keep resin tube away from heat. Be especially careful when
welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, from getting
on resin tube.
• Do not bend or twist resin tube during installation and removal.
• To keep the connecting portion clean, free of foreign materi-
als and to avoid damage, cover them completely with plastic
bags or something similar.
• Do not insert plug to prevent damage to O-ring in quick con-
nector.
PBIC1505E
PBIC1507E
PBIC1509E
PBIC0163E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст