Nissan Tiida C11. Instruction — part 147
DEF-36
< ON-VEHICLE REPAIR >
FILAMENT
ON-VEHICLE REPAIR
FILAMENT
Inspection and Repair
INFOID:0000000001697576
INSPECTION
1.
When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
2.
Attach probe circuit tester (in Volt range) to middle portion of
each filament.
3.
If a filament is burned out, circuit tester registers 0 or battery
voltage.
4.
To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)
SEL122R
SEL263
SEL265
FILAMENT
DEF-37
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth
REPAIRING PROCEDURE
1.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4.
After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5.
Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
SPECIAL REPAIR REQUIREMENT
PIIA0215E
SEL012D
SEL013D
DEF-38
< ON-VEHICLE REPAIR >
CONDENSER
CONDENSER
Exploded View
INFOID:0000000001697577
Removal and Installation
INFOID:0000000001697578
REMOVAL
1.
Remove the rear seat cushion and the rear seat back.
Refer to
XX-XX, "*****"
.
2.
Remove the rear kickplate, rear wheel well garnish and the rear pillar finisher.
Refer to
XX-XX, "*****"
.
3.
Remove bolt (A), and then remove condenser (1) from the vehi-
cle body.
INSTALLATION
Install in the reverse order of removal.
JMLIA0013ZZ
DLK-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
DLK
A
B
DLK
N
O
P
CONTENTS
DOOR & LOCK
WITH I-KEY, WITHOUT SUPER LOCK
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . . .
Work Flow . . . . . . . . . . . . . . . ...
INSPECTION AND ADJUSTMENT . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . .
FUNCTION DIAGNOSIS . . . . . . . ..
DOOR LOCK FUNCTION . . . . . . . . ..
DOOR LOCK AND UNLOCK SWITCH . . . . . .
DOOR LOCK AND UNLOCK SWITCH : System
Diagram . . . . . . . . . . . . . . . . ...
DOOR LOCK AND UNLOCK SWITCH : System
Description . . . . . . . . . . . . . . . ..
DOOR LOCK AND UNLOCK SWITCH :
Component Parts Location . . . . . . . . .
DOOR LOCK AND UNLOCK SWITCH :
Component Description . . . . . . . . . . ..
INTELLIGENT KEY . . . . . . . . . . . . ...
INTELLIGENT KEY : System Diagram . . . . ...
INTELLIGENT KEY : System Description . . . ...
INTELLIGENT KEY : Component Parts Location
INTELLIGENT KEY : Component Description . ...
DOOR REQUEST SWITCH . . . . . . . . . ...
DOOR REQUEST SWITCH : System Diagram . ..
DOOR REQUEST SWITCH : System Description
DOOR REQUEST SWITCH :
Component Parts Location . . . . . . . . .
DOOR REQUEST SWITCH :
Component Description . . . . . . . . . . ..
KEY REMINDER . . . . . . . . . . . . . .
KEY REMINDER : System Diagram . . . . . .
KEY REMINDER : System Description . . . . ...
KEY REMINDER : Component Parts Location . ..
KEY REMINDER : Component Description . . .
BACK DOOR OPENER FUNCTION . . . . .
BACK DOOR OPENER SWITCH . . . . . . . ..
BACK DOOR OPENER SWITCH : System Dia-
gram . . . . . . . . . . . . . . . . . .
BACK DOOR OPENER SWITCH : System De-
scription . . . . . . . . . . . . . . . . ...
BACK DOOR OPENER SWITCH :
Component Parts Location . . . . . . . . .
BACK DOOR OPENER SWITCH :
Component Description . . . . . . . . . . ..
TRUNK LID OPENER . . . . . . . . . ...
TRUNK LID OPENER SWITCH . . . . . . . . .
TRUNK LID OPENER SWITCH : System Diagram
.
TRUNK LID OPENER SWITCH : System Descrip-
tion . . . . . . . . . . . . . . . . . . ...
TRUNK LID OPENER SWITCH :
Component Parts Location . . . . . . . . .
TRUNK LID OPENER SWITCH :
Component Description . . . . . . . . . . ..
WARNING FUNCTION . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . .
Component Description . . . . . . . . . . ..
HAZARD AND BUZZER REMINDER FUNC-
TION . . . . . . . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст