Nissan Tiida C11. Instruction — part 727
EM-260
< PREPARATION >
[K9K]
PREPARATION
Commercial Service Tools
INFOID:0000000001381460
KV113B0220
(Mot. 1586)
Front oil seal drift set
Tool for installing crankshaft seals, timing end
KV113B0230
(Mot. 1632)
Camshaft seal insert
Tool for installing inlet camshaft seals
KV113B0240
(Rou. 15-01)
Shaft protector
Internal shaft protector
16 mm (0.63 in) dia.
KV113B0400
(Mot. 1592)
Compression gauge attachment
Connecting compression gauge and glow
plug holex
—
(Mot. 1606-A)
Camshaft pulley holder
Tool for locking sprockets for toothed timing
belt
—
(Mot. 1638)
Belt tension gauge
Setting drive belt tension
NISSAN tool number
(RENAULT tool No.)
Tool name
Description
MBIB0712E
E1BIA0053ZZ
MBIB0382E
NISSAN tool number
(RENAULT tool No.)
Tool name
Description
KV113B0030
(Mot. 11)
Crankshaft bearing remover
Crankshaft bearing extractor
KV113B0040
(Mot. 251-01)
Dial gauge stand set
Gauge stand used with KV113B0050 (Mot.
252-01)
MBIB0359E
MBIB0360E
PREPARATION
EM-261
< PREPARATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
KV113B0050
(Mot. 252-01)
Dial gauge stand set
Thrust plate for measuring the protrusion of
cylinder liners used with KV113B0040 (Mot.
251-01).
KV113B0090
(Mot. 1335)
Valve seal remover
Tool for removing valve stem seals
KV113B0180
(Mot. 1511-01)
Valve seal drift
Tool for installing valve stem seals
KV113B0200
(Mot. 1573)
Cylinder head stand
Cylinder head support
KV113E0010
(Mot. 1566)
Fuel spill tube spanner
Spanner for installing and removing injection
tubes
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
Instruction lift table caddy
Removing and installing engine
NISSAN tool number
(RENAULT tool No.)
Tool name
Description
MBIB0361E
MBIB0370E
MBIB0378E
MBIB0380E
MBIB0379E
NT052
ZZA1210D
EM-262
< PREPARATION >
[K9K]
PREPARATION
Piston ring expander
Removing and installing piston ring
(Mot. 588)
Liner retaining strap
(664000)
Cylinder head test container
Tool for testing the cylinder head, including: a
tray and the various kits suited for each model
of cylinder head (plug, sealing plate, blanking
plate).
Torx socket
Standard 1/2" (12.7 mm) square drive 8/12 /14
female torx socket.
(Mot. 1505)
(Mot. 1715)
Frequency meter
Tool for belt tension checking with frequency
Glow plug wrench
Articulated wrench for removing and installing
the glow plugs
Main bearing wrench
Wrench for removing main bearings
NISSAN tool number
(RENAULT tool No.)
Tool name
Description
NT030
MBIB0364E
MBIB0383E
MBIB1423E
MBIB0387E
MBIB0388E
DRIVE BELTS
EM-263
< ON-VEHICLE MAINTENANCE >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ON-VEHICLE MAINTENANCE
DRIVE BELTS
Exploded View
INFOID:0000000001381461
Inspection and Adjustment
INFOID:0000000001381462
INSPECTION
WARNING:
Be sure to perform when the engine is stopped.
1.
Inspect drive belt for cracks, fraying, wear and oil. Replace drive belt if necessary.
2.
Instructionly evaluate the drive belt tension (tension cannot be measured using frequency meter).
3.
Replace drive belt when tension is beyond normal operating limit.
CAUTION:
Auto-tensioner must be replaced with a new one when the belt is replaced.
ADJUSTMENT
Belt tensioning is not necessary, as it is automatically adjusted by auto-tensioner.
Removal and Installation
INFOID:0000000001381463
CAUTION:
• Replace any drive belt that has been removed with a new one.
• Auto-tensioner must be replaced with new one when the drive belt is replaced.
• Do not run the engine without the drive belt to avoid damaging the crankshaft pulley.
REMOVAL
1.
Remove engine undercover using power tool.
2.
Remove RH front wheel. Refer to
.
3.
Remove right side splash cover.
E1BIA0021ZZ
1.
Crankshaft pulley
2.
A/C compressor
3.
Drive belt
4.
Generator
5.
Drive belt auto-tensioner
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст