Nissan Tiida C11. Instruction — part 51
REAR DISC BRAKE
BR-11
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR DISC BRAKE
Inspection
INFOID:0000000001724674
PAD WEAR INSPECTION
• Inspect pad thickness through inspection hole on cylinder body.
Use a ruler or caliper for inspection if necessary. Refer to
.
BRA0010D
BR-12
< ON-VEHICLE REPAIR >
BRAKE PEDAL
ON-VEHICLE REPAIR
BRAKE PEDAL
Removal and Installation
INFOID:0000000001716977
COMPONENTS
REMOVAL
1.
Disconnect accelerator pedal position sensor harness connec-
tor.
2.
Remove stop lamp switch from brake pedal assembly.
3.
Remove snap pin and clevis pin from clevis of brake booster.
4.
Remove nuts from brake pedal bracket, and remove brake pedal
assembly from vehicle.
5.
Remove accelerator pedal from brake pedal assembly.
INSPECTION AFTER REMOVAL
• Check brake pedal upper rivet for deformation.
• Make sure that the lapping length of sub-bracket and slide plate is
at least 6.9 mm (0.272 in).
• Check brake pedal for bend, damage, and cracks on the welded
parts.
• Replace brake pedal assembly if any non-standard condition is
detected.
1.
Snap pin
2.
Stop lamp switch
3.
Clip
4.
Brake pedal assembly
5.
Clevis
6.
Brake pedal pad
7.
ASCD switch
AWFIA0084GB
SFIA2044E
SFIA2866E
BRAKE PEDAL
BR-13
< ON-VEHICLE REPAIR >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
• Check clevis pin and plastic stopper for damage and deformation.
Replace clevis pin as necessary.
INSTALLATION
Installation is in the reverse order of the removal.
• After installing brake pedal assembly to vehicle, adjust brake pedal. Refer to
.
• After installing accelerator pedal, check accelerator pedal. Refer to
ACC-3, "Removal and Installation"
.
SBR997
BR-14
< ON-VEHICLE REPAIR >
BRAKE TUBE AND HOSE
BRAKE TUBE AND HOSE
Hydraulic Circuit
INFOID:0000000001716982
NOTE:
LHD shown RHD similar.
CAUTION:
• All tubes and hoses must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning steering both clockwise and coun-
terclockwise.
• Brake tubes and hoses are an important safety part. Always disassemble the parts and retighten
their fittings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part
is detected.
• Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted surfaces of body, immediately wipe them with cloth and then wash it away with
water.
• Do not bend or twist brake hose sharply, or strongly pull it.
• When removing components, cover brake line connections so that dirt, dust, or other foreign mat-
ters do not get in.
• Refill using recommended brake fluid. Refer to
MA-19, "Fluids and Lubricants"
• Never reuse drained brake fluid.
Front Brake Tube and Hose
INFOID:0000000001716983
REMOVAL
1.
Front disc brake
2.
Brake master cylinder
3.
Brake booster
4.
Rear drum brake
5.
Connector
6.
ABS actuator and electric unit (con-
trol unit), if equipped
7.
Brake tube
8.
Brake hose
:
Union bolt
:
Connector bolt
:
Flare nut
18.2 N.m (1.9 kg-m, 13.0 ft-lb)
10.0 N.m (1.0 kg-m, 87.0 in-lb)
16.2 N.m (1.7 kg-m, 12.0 ft-lb)
SFIA3068E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст