Nissan Tiida C11. Instruction — part 1180
SEC-92
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B2190, P1614 NATS ANTENNA AMP.
B2190, P1614 NATS ANTENNA AMP.
Description
INFOID:0000000001532070
Performs ID verification through BCM and NATS antenna amplifier when ignition knob switch is pressed.
Prohibits the start of engine when an unregistered ID of mechanical key is used.
DTC Logic
INFOID:0000000001532071
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Insert ignition key into the key cylinder.
2.
Turn ignition switch ON.
3.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
XX-XX, "*****"
.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000001532072
1.
CHECK NATS ANTENNA AMP. INSTALLATION
Check NATS antenna amp. installation. Refer to
XX-XX, "*****"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Reinstall NATS antenna amp. correctly.
2.
CHECK NATS IGNITION KEY ID CHIP
Start engine with another registered NATS ignition key.
Does the engine start?
YES
>> • Ignition key ID chip is malfunctioning.
• Replace the ignition key.
• Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Instruction”.
NO
>> GO TO 3.
3.
CHECK POWER SUPPLY FOR NATS ANTENNA AMP.
1.
Turn ignition switch ON.
2.
Check voltage between NATS antenna amp. connector M21 terminal 3 and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2190
NATS ANTENNA
AMP
• Inactive communication between NATS antenna
amp. and BCM.
• Mechanical key is malfunctioning.
• Harness or connectors
(The NATS antenna amp. circuit is
open or shorted)
• Mechanical key
• NATS antenna amp.
• BCM
P1614
B2190, P1614 NATS ANTENNA AMP.
SEC-93
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace fuse or harness.
4.
CHECK NATS ANTENNA AMP. GROUND LINE CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between NATS antenna amp. connector M21 terminal 2 and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK NATS ANTENNA AMP. SIGNAL LINE
1.
Turn ignition switch ON.
2.
Using analog tester, check voltage between NATS antenna
amp. connector M21 terminal 1 and ground.
Is the inspection result normal?
YES
>> NATS antenna amp. is malfunctioning.
NO
>> • Repair or replace harness.
NOTE:
If harness is OK, replace BCM, perform initialization with CONSULT-III. For initialization, refer to
“CONSULT-III Operation Instruction”.
3 - Ground
: Battery voltage
ALKIA0850ZZ
2 - Ground
: Continuity should exist
ALKIA0851ZZ
LIIA1280E
Terminals
Position of ignition key cylinder
Voltage (V)
(Approx.)
( + )
( - )
1
Ground
Before inserting ignition key
Battery voltage
After inserting ignition key
Pointer of tester should move for approx. 30 seconds,
then return to battery voltage
Just after turning ignition switch
ON
Pointer of tester should move for approx. 1 second, then
return to battery voltage
SEC-94
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B2191, P1615 DIFFERENCE OF KEY
B2191, P1615 DIFFERENCE OF KEY
Description
INFOID:0000000001404177
Performs ID verification through BCM when ignition switch is ON position.
Prohibits the release of steering lock or start of engine when an unregistered key is used.
DTC Logic
INFOID:0000000001404178
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Insert ignition key into the key cylinder.
2.
Press the ignition knob switch.
3.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000001404179
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all ignition keys.
For initialization and registration of ignition key. Refer to CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered ignition key?
YES
>> Ignition key was unregistered.
NO
>>
BCM is malfunctioning.
• Replace BCM. Refer to
XX-XX, "*****"
.
• Perform initialization again
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2191
DIFFERENCE OF
KEY
The ID verification results between BCM and igni-
tion key are NG. The registration is necessary.
• Ignition key
P1615
B2192, P1611 ID DISCORD, IMMU-ECM
SEC-95
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2192, P1611 ID DISCORD, IMMU-ECM
Description
INFOID:0000000001404180
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with
ECM if ignition switch is turned ON starts the engine if the ID is OK. ECM prevents the engine from starting if
the ID is not registered.
DTC Logic
INFOID:0000000001404181
DTC DETECTION LOGIC
NOTE:
• If DTC B2192 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2192 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000001404182
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all ignition keys.
For initialization and registration of ignition key. Refer to CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered ignition key?
YES
>> ID was unregistered.
NO
>> GO TO 2.
2.
PEPLACE BCM
1.
Replace BCM. Refer to
XX-XX, "*****"
.
2.
Perform initialization with CONSULT-III. Re-register all ignition keys.
For initialization and registration of ignition key. Refer to “CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered ignition key?
YES
>> BCM is malfunctioning.
NO
>> GO TO 3.
3.
PEPLACE ECM
1.
Replace ECM.
2.
Perform initialization with CONSULT-III. Re-register all ignition keys.
For initialization and registration of ignition key. Refer to “CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered ignition key?
YES
>> ECM is malfunctioning.
NO
>> GO TO 4.
4.
CHECK INTERMITTENT INCIDENT
Refer to @@@.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2192
ID DISCORD BCM-
ECM
The ID verification results between BCM and ECM
are NG. The registration is necessary.
• BCM
• ECM
P1611
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст