Nissan Tiida C11. Instruction — part 182
DLK-138
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
STOP LAMP SWITCH (A/T)
STOP LAMP SWITCH (A/T)
Diagnosis Procedure
INFOID:0000000001516691
1.
CHECK STOP LAMP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key unit connector.
3.
Check voltage between Intelligent Key unit harness connector
M52 terminal 26 and ground.
Is the inspection result normal?
YES
>> Stop lamp switch is OK.
NO
>> GO TO 2.
2.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
Disconnect stop lamp switch connector.
2.
Check voltage between stop lamp switch harness connector
E13 terminal 1 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness between stop lamp switch
power supply circuit and fuse.
3.
CHECK STOP LAMP SWITCH OPERATION
Check continuity between stop lamp switch terminals 1 and 2.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace stop lamp switch.
4.
CHECK STOP LAMP SWITCH CIRCUIT
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M52
26
Ground
Brake pedal
depressed
Battery volt-
age
Brake pedal
released
0
WIIA1207E
1 - Ground
: Battery voltage
WIIA1255E
Component
Terminals
Condition
Continuity
Stop lamp
switch
1
2
Brake pedal depressed
Yes
Brake pedal released
No
WIIA1256E
STOP LAMP SWITCH (A/T)
DLK-139
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Check continuity between Intelligent Key unit harness connector
(A) M52 terminal 26 and stop lamp switch harness connector (B)
E13 terminal 2.
2.
Check continuity between Intelligent Key unit harness connector
M52 terminal 26 and ground.
Is the inspection result normal?
YES
>> Check condition of harness and connector.
NO
>> Repair or replace harness.
26 - 2
: Continuity should exist.
26 - Ground
: Continuity should not exist.
WIIA1257E
DLK-140
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
STOP LAMP SWITCH (M/T)
STOP LAMP SWITCH (M/T)
Diagnosis Procedure
INFOID:0000000001516670
1.
CHECK STOP LAMP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key unit connector.
3.
Check voltage between Intelligent Key unit harness connector
M52 terminal 26 and ground.
Is the inspection result normal?
YES
>> Stop lamp switch is OK.
NO
>> GO TO 2.
2.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
Disconnect stop lamp switch connector.
2.
Check voltage between stop lamp switch harness connector
M203 terminal 1 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness between stop lamp switch
power supply circuit and fuse.
3.
CHECK STOP LAMP SWITCH OPERATION
Check continuity between stop lamp switch terminals 1 and 2.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace stop lamp switch.
4.
CHECK STOP LAMP SWITCH CIRCUIT
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M52
26
Ground
Brake pedal
depressed
Battery volt-
age
Brake pedal
released
0
WIIA1207E
1 - Ground
: Battery voltage
WIIA1208E
Component
Terminals
Condition
Continuity
Stop lamp
switch
1
2
Brake pedal depressed
Yes
Brake pedal released
No
WIIA1209E
STOP LAMP SWITCH (M/T)
DLK-141
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Check continuity between Intelligent Key unit harness connector
(A) M52 terminal 26 and stop lamp switch harness connector (B)
M203 terminal 2.
2.
Check continuity between Intelligent Key unit harness connector
M52 terminal 26 and ground.
Is the inspection result normal?
YES
>> Check condition of harness and connector.
NO
>> Repair or replace harness.
26 - 2
: Continuity should exist.
26 - Ground
: Continuity should not exist.
WIIA1210E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст