Nissan Tiida C11. Instruction — part 670
EM-32
< ON-VEHICLE REPAIR >
[HR16DE]
EXHAUST MANIFOLD
EXHAUST MANIFOLD
Exploded View
INFOID:0000000001381400
Removal and Installation
INFOID:0000000001381401
REMOVAL
1.
EXT-20, "Removal and Installation"
.
2.
Remove the engine room cover.
3.
Remove exhaust front tube. Refer to
.
4.
Remove the harness bracket of heated oxygen sensor 1 from the cylinder head.
5.
Remove exhaust manifold cover.
6.
Remove the heated oxygen sensor 1.
1.
Exhaust manifold cover
2.
Exhaust manifold cover
3.
Harness bracket
4.
Heated oxygen sensor 1
5.
Exhaust manifold stay
6.
Exhaust manifold
7.
Gasket
8.
Stud bolt
9.
Heat insulator
: Engine front
PBIC4750E
EXHAUST MANIFOLD
EM-33
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Using heated oxygen sensor wrench [SST: KV10117100] (A),
remove heated oxygen sensor 1.
CAUTION:
Handle heated oxygen sensor 1 carefully and avoid
impacts.
NOTE:
The exhaust manifold can be removed and installed without
removing the heated oxygen sensor 1 (Disassembly of harness
connector is necessary).
7.
Remove exhaust manifold side mounting bolt of exhaust manifold stay.
8.
Remove exhaust manifold.
• Loosen nuts in the reverse of the order shown.
9.
Remove gasket.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
10. Remove exhaust manifold cover from back of exhaust manifold.
INSPECTION AFTER REMOVAL
Mounting Surface Distortion
• Use suitable tools (A) and (B) to check distortion of exhaust mani-
fold mounting surface as shown.
• Replace exhaust manifold if outside the limit.
INSTALLATION
Installation is in the reverse order of removal.
Exhaust Manifold
PBIC3654E
: Engine front
PBIC3774E
Limit
: 0.3 mm (0.012 in)
PBIC3530J
EM-34
< ON-VEHICLE REPAIR >
[HR16DE]
EXHAUST MANIFOLD
1.
Tighten nuts in numerical order shown.
2.
Tighten to the specified torque again.
: Engine front
PBIC3774E
FUEL INJECTOR AND FUEL TUBE
EM-35
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
FUEL INJECTOR AND FUEL TUBE
Exploded View
INFOID:0000000001381403
CAUTION:
Never remove or disassemble parts unless instructed as shown.
Removal and Installation
INFOID:0000000001381404
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
REMOVAL
1.
Release the fuel pressure. Refer to
(EURO-OBD),
EURO-OBD).
2.
Remove intake manifold. Refer to
1.
Quick connector cap
2.
Fuel feed hose
3.
Fuel tube
4.
Fuel tube protector
5.
O-ring (black)
6.
Clip
7.
Fuel injector
8.
O-ring (green)
PBIC3663E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст