Nissan Tiida C11. Instruction — part 790
FRONT DRIVE SHAFT
FAX-25
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Support Bearing
1.
Install new dust shield on drive shaft
CAUTION:
Do not reuse dust shield.
2.
Press support bearing onto drive shaft.
3.
Install new snap ring.
CAUTION:
Do not reuse snap ring.
4.
Install new dust shield
CAUTION:
Do not reuse dust shield.
Damper
1.
Secure damper with new damper bands.
CAUTION:
Do not reuse damper bands.
YAX007
YAX008
“A”
: 230 – 236 mm (9.06 – 9.29 in)
“B”
: 70 mm (2.76 in)
FAC0156D
FAX-26
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Drive Shaft
INFOID:0000000001716805
Dynamic Damper
INFOID:0000000001716806
Joint type
Wheel side
Transaxle side
Grease quantity
70 - 90 g (2.5 - 3.2 oz)
130 - 140 g (4.6 - 4.9 oz)
Boots installed length
Left side
142 mm (5.59 in)
176 mm (6.93 in) (A/T model)
181.2 mm (7.13 in) (M/T models)
Right side
178 mm (7.01 in) (A/T model)
168 mm (6.61 in) (M/T models)
Dimension A
230 – 236 mm (9.06 – 9.29 in)
Dimension B
70 mm (2.76 in)
FAC0156D
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
ON-VEHICLE MAINTENANCE . . . . . .
FUEL SYSTEM . . . . . . . . . . . . .
Checking Fuel Line . . . . . . . . . . . . ...
General Precaution . . . . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . ..
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . . ..
HR16DE, HR18DE . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
K9K . . . . . . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
FUEL TANK . . . . . . . . . . . . . ..
HR16DE, HR18DE . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
K9K . . . . . . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
FL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001722973
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SR inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст