Nissan Tiida C11. Instruction — part 745
EM-332
< DISASSEMBLY AND ASSEMBLY >
[K9K]
CYLINDER BLOCK
• Measure the side clearance of piston ring and piston ring groove
with a feeler gauge (A).
• If the measured value exceeds the limit, replace piston ring, and
measure again. If it still exceeds the limit, replace piston also.
PISTON RING END GAP
• Lubricate with new engine oil to piston (1) and piston ring (2), and
then insert (A) piston ring until middle of cylinder (B) with piston,
and measure piston ring end gap with a feeler gauge (C).
• If the measured value exceeds the limit, replace piston ring.
CRANKSHAFT MAIN JOURNAL DIAMETER
Use micrometer to measure crankshaft main journal diameter.
CRANKSHAFT PIN JOURNAL DIAMETER
Use micrometer to measure crankshaft pin journal diameter.
Standard
: Refer to
PBIC3280J
Standard
: Refer to
PBIC3267J
Standard
: Refer to
FEM114
Standard
: Refer to
PBIC0127E
SERVICE DATA AND SPECIFICATIONS (SDS)
EM-333
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000001381516
GENERAL SPECIFICATIONS
Drive Belt
INFOID:0000000001381517
DRIVE BELT
Camshaft
INFOID:0000000001381518
CAMSHAFT
Unit: mm (in)
Cylinder arrangement
In-line 4
Displacement
cm
3
(cu in)
1.461 (89.15)
Bore and stroke
mm (in)
76 x 80.5 (2.99 x 3.17)
Valve arrangement
SOHC
Firing order
1-3-4-2
Number of piston rings
Compression
2
Oil
1
Number of main bearings
5
Compression ratio
15.3
Compression pressure
kPa (bar, kg/cm
2
, psi)
Maximum pressure must be at least 1,800
(18, 18.36, 261)
Valve timing
a
b
c
d
e
f
200
°
191
°
-9
°
20
°
-7
°
27
°
PBIC0187E
Tension of drive belt
Auto adjustment by auto-tensioner
Items
Standard
Camshaft bracket inner diameter
No. 1, 2, 3, 4, 5
25.04 - 25.06 (0.9858 - 0.9866)
No. 6
28.04 - 28.06 (1.1039 - 1.1047)
Camshaft journal diameter
No. 1, 2, 3, 4, 5
24.979 - 25.000 (0.9834 - 0.9843)
No. 6
27.979 - 28.000 (1.1015 - 1.1024)
Camshaft end play
0.080 - 0.178 (0.0031 - 0.0070)
Camshaft runout
Less than 0.05 (0.0020)
EM-334
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
SERVICE DATA AND SPECIFICATIONS (SDS)
VALVE LIFTER
Unit: mm (in)
VALVE CLEARANCE
Unit: mm (in)
AVAILABLE VALVE LIFTER
Unit: mm (in)
Camshaft cam height “A”
Intake
43.985 - 44.045 (1.7317 - 1.7341)
Exhaust
44.565 - 44.625 (1.7545 - 1.7569)
Items
Standard
SEM671
Items
Standard
Valve lifter outer diameter
34.965 - 34.985 (1.3767 - 1.3774)
Valve lifter hole diameter
35.000 - 35.040 (1.3780 - 1.3795)
Valve lifter clearance
0.015 - 0.075 (0.0006 - 0.0030)
Items
Cold
Intake
0.125 - 0.250 (0.0049 - 0.0098)
Exhaust
0.325 - 0.450 (0.0128 - 0.0177)
Part number
Thickness
13229BN700
7.550 (0.2972)
13229BN701
7.575 (0.2982)
13229BN702
7.600 (0.2992)
13229BN703
7.625 (0.3002)
13229BN704
7.650 (0.3012)
13229BN705
7.675 (0.3022)
13229BN706
7.700 (0.3031)
13229BN707
7.725 (0.3041)
13229BN708
7.750 (0.3051)
13229BN709
7.775 (0.3061)
13229BN710
7.800 (0.3071)
13229BN711
7.825 (0.3081)
13229BN712
7.850 (0.3091)
13229BN713
7.875 (0.3100)
13229BN714
7.900 (0.3110)
13229BN715
7.925 (0.3120)
13229BN716
7.950 (0.3130)
13229BN717
7.975 (0.3140)
SERVICE DATA AND SPECIFICATIONS (SDS)
EM-335
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Cylinder Head
INFOID:0000000001381519
CYLINDER HEAD
Unit: mm (in)
VALVE DIMENSIONS
13229BN718
8.000 (0.3150)
13229BN719
8.025 (0.3159)
13229BN720
8.050 (0.3169)
13229BN721
8.075 (0.3179)
13229BN722
8.100 (0.3189)
13229BN723
8.125 (0.3199)
13229BN724
8.150 (0.3209)
Part number
Thickness
Items
Standard
Cylinder head gasket thickness
0.68 - 0.74 (0.0269 - 0.0291)
Head surface distortion
Less than 0.05 (0.002)
Normal cylinder head height “H”
127 (5.000)
E1BIA0063ZZ
Items
Standard
Valve head diameter “D”
mm (in)
Intake
33.38 - 33.62 (1.314 - 1.324)
Exhaust
28.88 - 29.12 (1.137 - 1.146)
Valve length “L”
mm (in)
Intake
100.74 - 101.16 (3.9661 - 3.9827)
Exhaust
100.54 - 100.96 (3.9583 - 3.9748)
Valve stem diameter “d”
mm (in)
Intake
5.969 - 5.985 (0.2350 - 0.2356)
Measuring point (X1) is 41 (1.61)
Exhaust
5.955 - 5.971 (0.2344 - 0.2351)
Measuring point (X1) is 41 (1.61)
Valve seat angle “
α
”
degree
45
°
00
′
(45.00
°
)
Valve margin “T”
mm (in)
1.0 (0.039)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст