Nissan Tiida C11. Instruction — part 737
EM-300
< ON-VEHICLE REPAIR >
[K9K]
CAMSHAFT
7.
Screw the collar nut until the cover touches the cylinder head.
8.
Install camshaft sprocket and sprocket holder [SST: — (Mot.
1606-A)] (A).
9.
Install timing belt. Refer to
EM-291, "Removal and Installation"
.
10. Installation is in the reverse order of removal.
Inspection
INFOID:0000000001381503
INSPECTION AFTER REMOVAL
Camshaft Runout
1.
Put V-block on a precise flat table, and support No. 2 and 4 journal of camshaft.
CAUTION:
Never support No. 1 journal (on the side of camshaft
sprocket) because it has a different diameter from the other
four locations.
2.
Set dial indicator (A) vertically to No. 3 journal.
3.
Turn camshaft in one direction and measure the camshaft
runout on dial indicator. (Total indicator reading)
4.
If it exceeds the limit, replace camshaft.
Camshaft Cam Height
1.
Measure the camshaft cam height with a suitable tool (A).
2.
If it exceeds the limit, replace camshaft.
Camshaft End Play
MBIB0433E
E1BIA0054ZZ
Standard
: Refer to
.
PBIC3177J
Standard
: Refer to
.
PBIC3178J
CAMSHAFT
EM-301
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1.
Install the camshaft.
2.
Install the camshaft brackets.
3.
Check the end play.
Valve Lifter
1.
Measure outer diameter of valve lifter.
2.
Measure inner diameter of valve lifter hole in cylinder head.
3.
Calculate the valve lifter clearance.
(Valve lifter clearance) = (Valve lifter hole inner diameter) – (Valve lifter diameter)
Standard
: Refer to
MBIB0420E
Intake and exhaust
: Refer to
Intake and exhaust
: Refer to
Intake and exhaust
: Refer to
EM-302
< REMOVAL AND INSTALLATION >
[K9K]
ENGINE ASSEMBLY
REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Exploded View
INFOID:0000000001381504
Removal and Installation
INFOID:0000000001381505
WARNING:
• Situate vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• For engines not equipped with engine slingers, attach proper slingers and bolts described in PARTS
CATALOG.
CAUTION:
• Always be careful to work safely, avoid forceful or uninstructed operations.
• Do not start working until exhaust system and coolant are cool enough.
• If items or work required are not covered by the main engine section, follow the procedures in the
applicable sections.
• Always use the support point specified for lifting.
• Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for unavoid-
able reasons, support at the rear axle jacking point with transmission jack or similar tool before
starting work, in preparation for the backward shift of center of gravity.
• For supporting points for lifting and jacking rear axle, refer to
GI-48, "Garage Jack and Safety Stand
or
.
REMOVAL
Description of Work
1.
Engine mounting insulator LH
2.
Engine mounting frame support LH
3.
Engine mounting bracket LH
4.
Upper torque rod
5.
Engine mounting insulator RH
6.
Engine mounting bracket RH (upper)
7.
Engine mounting bracket RH (lower)
8.
Lower torque rod bracket
9.
Lower torque rod
: Vehicle front
AWBIA0162GB
ENGINE ASSEMBLY
EM-303
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Remove engine and transaxle assembly from vehicle down ward. Separate engine and transaxle.
Preparation
Remove the following parts.
• Battery ground cable.
• Engine undercover.
• LH and RH front wheels. Refer to
.
• LH and RH fender protectors. Refer to
EXT-22, "Removal and Installation"
Engine Room
1.
Drain engine coolant. Refer to
.
CAUTION:
Perform when engine is cold.
2.
Remove lower radiator hose. Refer to
3.
Drain transaxle fluid. Refer to
.
4.
Disconnect clutch tube at clutch housing and drain clutch fluid.
NOTE:
Cover clutch tube ends to prevent contamination.
5.
Remove hood. Refer to
DLK-214, "Removal and Installation"
.
6.
Remove cowl top cover and cowl top extension assembly. Refer to
EXT-20, "Removal and Installation"
7.
Remove battery and battery trap. Refer to
PG-6, "Removal and Installation"
.
8.
Disconnect engine room harness from the engine side and position aside.
9.
Remove the air duct (inlet). Refer to
.
10. Remove engine cover.
11. Remove blow-by hose.
12. Remove air cleaner case and air duct (suction). Refer to
EM-269, "Removal and Installation"
.
13. Remove reservoir tank and hoses. Refer to
.
14. Remove charge air cooler hoses and tubes. Refer to
15. Remove vacuum hose. Refer to
EM-280, "Removal and Installation"
16. Disconnect fuel feed and return hoses, and plug it to prevent fuel from draining.
17. Remove radiator upper hose. Refer to
18. Disconnect heater hoses.
19. Disconnect transaxle side harness.
20. Disconnect breather hose transaxle side.
21. Disconnect shift cable and select cable. Refer to
22. Remove cooling fan. Refer to
CO-64, "Removal and Installation"
.
23. Remove radiator. Refer to
24. Disconnect all the body-side vacuum hoses and air hoses at engine side.
Vehicle Underbody
1.
Remove drive shaft assembly RH and LH. Refer to Removal and Installation.
2.
Remove exhaust front tube. Refer to
.
3.
Remove drive belt. Refer to
EM-263, "Removal and Installation"
4.
Remove A/C compressor and position aside.
NOTE:
Secure it to body with a rope to avoid putting load on A/C lines.
5.
Remove lower torque rod. Refer to
Removal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст