Nissan Tiida C11. Instruction — part 685
EM-92
< REMOVAL AND INSTALLATION >
[HR16DE]
ENGINE ASSEMBLY
4.
Remove engine mounting insulator (RH) (1), engine mounting
bracket (RH) (2) and engine mounting stay (3).
5.
Remove engine mounting through bolt-securing nut (A).
6.
Carefully lower jack, or raise lift to remove the engine and the transaxle assembly.
CAUTION:
• Make sure that no part interferes with the vehicle side.
• Before and during this lifting, always check if any harnesses are left connected.
• During the removal, always be careful to prevent the vehicle from falling off the lift due to
changes in the center of gravity.
• If necessary, support the vehicle by setting jack or suitable tool at the rear.
Separation
1.
Remove starter motor. Refer to
STR-13, "Removal and Installation"
.
2.
Lift with a hoist and separate the engine from the transaxle assembly. Refer to
.
INSTALLATION
Installation is in the reverse order of removal.
• Do not allow engine oil to get on engine mounting insulator. Be careful not to damage engine mounting insu-
lator.
• Make sure that each mounting insulator is seated properly, and tighten mounting nuts and bolts.
• Tighten engine mounting insulator (RH) bolts in the numerical
order shown.
Inspection
INFOID:0000000001381426
INSPECTION AFTER INSTALLATION
Inspection for Leaks
• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-19, "Fluids and Lubricants"
.
• Use procedure below to check for fuel leakage.
- Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leak-
age at connection points.
- Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
• Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids includ-
ing engine oil and engine coolant.
• Bleed air from lines and hoses of applicable lines, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
4
: Engine mounting insulator (LH)
JPBIA0512ZZ
: Vehicle front
JPBIA0280ZZ
ENGINE ASSEMBLY
EM-93
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Summary of the inspection items:
*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.
Items
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
EM-94
< DISASSEMBLY AND ASSEMBLY >
[HR16DE]
ENGINE STAND SETTING
DISASSEMBLY AND ASSEMBLY
ENGINE STAND SETTING
Setting
INFOID:0000000001381427
NOTE:
Explained here is how to disassemble with engine stand supporting transmission surface. When using differ-
ent type of engine stand, note with difference in steps and etc.
1.
Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the
engine. Refer to
2.
Remove clutch cover and clutch disc. Refer to
CL-13, "Removal and Installation"
.
3.
Remove flywheel.
• Secure flywheel with a stopper plate [SST: KV11105210], and remove mounting bolts.
CAUTION:
• Never disassemble flywheel.
• Never place flywheel with signal plate facing down.
• When handling signal plate, take care not to damage or scratch it.
• Handle signal plate in a manner that prevents it from becoming magnetized.
4.
Lift the engine with a hoist to install it onto widely use engine stand.
CAUTION:
• Use the engine stand that has a load capacity [approximately 135 kg (298 lb) or more] large
enough for supporting the engine weight.
• If the load capacity of stand is not adequate, remove the following parts beforehand to reduce the poten-
tial risk of overturning stand.
- Intake manifold: Refer to
- Exhaust manifold: Refer to
- Rocker cover: Refer to
NOTE:
The figure shows an example of widely use engine stand that
can support mating surface of transaxle with flywheel removed.
CAUTION:
Before removing the hanging chains, make sure the engine
stand is stable and there is no risk of overturning.
5.
Drain engine oil. Refer to
.
6.
Drain engine coolant by removing water drain plug (1) from
inside of the engine.
Use Genuine Liquid Gasket or equivalent.
PBIC0085E
: Engine front
PBIC3742E
ENGINE UNIT
EM-95
< DISASSEMBLY AND ASSEMBLY >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ENGINE UNIT
Disassembly
INFOID:0000000001381428
1.
Remove intake manifold. Refer to
2.
Remove exhaust manifold. Refer to
.
3.
Remove oil pan (lower). Refer to
4.
Remove ignition coil, spark plug and rocker cover. Refer to
.
5.
Remove fuel injector and fuel tube. Refer to
6.
Remove timing chain. Refer to
.
7.
Remove camshaft. Refer to
8.
Remove cylinder head. Refer to
EM-80, "Removal and Installation"
Assembly
INFOID:0000000001381429
Assembly is the reverse order of disassembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст