Nissan Tiida C11. Instruction — part 1376
REPAIR FOR COMPONENT PARTS
TM-555
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NOTE:
Install two dish plates fitting each installation direction with
reverse clutch drum groove displaced slightly.
6.
Install snap ring (1) using suitable tool (A).
7.
Measure clearance between retaining plate and snap ring using
feeler gauge. If not within allowable limit, select proper retaining
plate.
8.
Check operation of reverse clutch. Refer to
.
High Clutch
INFOID:0000000001731441
COMPONENTS
SAT170D
SCIA7024J
Specified clearance
Standard and allowable limit:
.
SAT174D
SCIA6741E
TM-556
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
DISASSEMBLY
1.
Check operation of high clutch.
a.
Apply compressed air into the oil hole (A) of input shaft assem-
bly (high clutch drum) at the location as shown.
CAUTION:
Block the oil hole (A) on the opposite side with lint-free
cloth (B).
b.
Check to see that retaining plate moves to snap ring.
c.
If retaining plate does not contact snap ring:
• High clutch piston seal might be damaged.
2.
Remove seal rings from input shaft assembly (high clutch drum).
3.
Remove snap ring using suitable tool.
4.
Remove retaining plate, drive plates and driven plates.
5.
Set Tool (A) on cancel cover, and remove snap ring (1) from
input shaft assembly (high clutch drum) while compressing
spring retainer assembly.
CAUTION:
Do not expand snap ring (1) excessively.
1.
Seal ring
2.
Driven plate
3.
Retaining plate
4.
Snap ring
5.
Drive plate
6.
Snap ring
7.
Cancel cover
8.
Spring retainer assembly
9.
High clutch Piston
10. Input shaft assembly (high clutch
drum)
SCIA7032E
SCIA4890E
SCIA4891E
Tool number:
KV31103200
SCIA6001J
REPAIR FOR COMPONENT PARTS
TM-557
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
Remove cancel cover (1) and spring retainer assembly (2) from
input shaft assembly (high clutch drum) (3).
CAUTION:
Do not remove return springs from spring retainers.
7.
Apply compressed air into the oil hole (A) at the location as
shown to remove high clutch piston from input shaft assembly
(high clutch drum).
CAUTION:
• Do not blow air in too quickly, or high clutch piston and
ATF could jump out. Carefully blow air little by little while
protecting with lint-free cloth (B).
• Block the oil hole on the opposite side with lint-free cloth
(B).
INSPECTION
High Clutch Snap Ring
Check for deformation, fatigue or damage. Replace if necessary.
High Clutch Drive Plates
• Check facing for burns, cracks or damage. Replace if necessary.
• Measure thickness of facing.
CAUTION:
• Measure the thickness at 3 locations and find the average.
• Inspect ALL drive plates.
• Replace if the thickness is below the allowable limit.
High Clutch Spring Retainer Assembly
Check length (L) of springs retainer assembly. Replace if damaged,
deformed or worn.
CAUTION:
Do not remove return springs (A) from spring retainers (B).
High Clutch Piston and Cancel Cover
Check for deformation or damage. Replace if necessary.
Input Shaft Assembly (High Clutch Drum)
Check for deformation or damage. Replace if necessary.
Seal Ring Clearance
SCIA7036E
SCIA7033E
Thickness of drive plate
Standard and allowable limit:
.
SAT162D
Length (L):
20.6 mm (0.811 in)
SCIA7038E
TM-558
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
• Install new seal rings onto input shaft assembly (high clutch drum).
• Measure clearance between seal ring and ring groove.
• If not within allowable limit, replace input shaft assembly (high
clutch drum).
ASSEMBLY
1.
Install high clutch piston by turning it slowly.
CAUTION:
Apply ATF to inner surface of input shaft assembly (high
clutch drum) and high clutch piston.
2.
Install spring retainer assembly (2) and cancel cover (1) on input
shaft assembly (high clutch drum) (3).
3.
Set Tool A on cancel cover, and install snap ring (1) to input
shaft assembly (high clutch drum) while slowly compressing
spring retainer assembly.
CAUTION:
• Do not expand snap ring (1) excessively.
• Install spring retainer assembly without tilting.
Standard clearance and allowable limit:
SCIA4901E
SAT111F
SCIA7036E
Tool number:
KV31103200
SCIA6001J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст