Nissan Tiida C11. Instruction — part 120
CL-14
< SERVICE INFORMATION >
CLUTCH DISC, CLUTCH COVER AND FLYWHEEL
• Use a suitable tool to measure the depth to clutch disc facing rivet
heads. If it exceeds the allowable wear limit, replace clutch disc.
Clutch Cover
Check clutch cover installed on vehicle for unevenness of diaphragm
spring toe height.
• If out of limit, adjust the height using Tool (A).
• Check clutch cover thrust ring for wear or breakage. If wear or
breakage is found, replace clutch cover assembly.
NOTE:
• Worn thrust ring will generate a beating noise when tapped at the
rivet with a suitable tool.
• Broken thrust ring will make a clinking sound when cover is shaken up and down.
• If a trace of burn or discoloration is found on the clutch cover pressure plate to clutch disc contact surface,
repair the surface with sandpaper. If surface is damaged or distorted, replace the assembly.
Flywheel Runout
• Check contact surface of flywheel for slight burns or discoloration.
Repair flywheel with emery paper.
• Check the flywheel runout. Refer to
EM-219, "Inspection After Dis-
(K9K).
CAUTION:
Measure flywheel outer face (not on knock pin and clutch cover
mounting hole).
INSTALLATION
1.
Clean clutch disc and input shaft splines to remove grease and dust caused by abrasion.
2.
Apply recommended grease to clutch disc and input shaft splines.
CAUTION:
Be sure to apply grease to the points specified. Otherwise, noise, poor disengagement, or damage
to the clutch may result. Excessive grease may cause slip or shudder. If it adheres to CSC seal, it
will cause clutch fluid leakage. Wipe off excess grease.
3.
Install clutch disc using tool.
4.
Install clutch cover. Pre-tighten clutch cover bolts.
Wear limit of facing
surface to rivet head
: 0.3 mm (0.012 in)
SCL229
Uneven limit
: 0.7 mm (0.028 in) or less
Tool number A
: ST20050240 ( — )
PCIB1502E
PBIC2646E
Tool number
: KV30101000 ( — )
CLUTCH DISC, CLUTCH COVER AND FLYWHEEL
CL-15
< SERVICE INFORMATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
5.
Tighten clutch cover bolts evenly in two steps in the order
shown.
6.
Install the transaxle, refer to
EM-219, "Inspection After Disas-
(K9K).
PCIB1772E
CL-16
< SERVICE INFORMATION >
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Clutch Control System
INFOID:0000000001375300
Clutch Pedal
INFOID:0000000001375301
Clutch Disc
INFOID:0000000001375302
Clutch Cover
INFOID:0000000001375303
Type of clutch control
Hydraulic
Clearance
″
A
″
between clutch pedal and ASCD switch threaded
end while clutch pedal is fully released (if equipped).
0.74 - 1.96 mm (0.0291 - 0.0772 in)
Clearance
″
C
″
between clutch pedal and clutch interlock switch
threaded end while clutch pedal is fully depressed.
0.74 - 1.96 mm (0.0291 - 0.0772 in)
Model
225
Facing size (outer dia.
×
inner dia.
×
thickness)
225 mm
×
160 mm
×
3.2 mm (8.86 in
×
6.30 in
×
0.126 in)
Thickness of disc assembly with load
7.2 - 7.6 mm (0.283 - 0.299 in) with 5,394 N (550 kg, 1,213 lb)
Runout limit/diameter of the area to be measured
1.0 mm (0.039 in) / 215 mm (8.46 in) dia.
Maximum spline backlash (at outer edge of disc)
1.0 mm (0.039 in)
Wear limit of facing surface to rivet head
0.3 mm (0.012 in)
Set-load
5,394 N (550 kg, 1,213 lb)
Diaphragm spring lever height
20 - 22 mm (0.79 - 0.87 in)
Uneven limit diaphragm spring toe height
0.7 mm (0.028 in) or less
CO-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
CO
A
CO
N
O
P
CONTENTS
ENGINE COOLING SYSTEM
HR16DE
FUNCTION DIAGNOSIS . . . . . . . ...
DESCRIPTION . . . . . . . . . . . . .
Engine Cooling System . . . . . . . . . . .....
Engine Cooling System Schematic . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . ...
OVERHEATING CAUSE ANALYSIS . . . . ..
Troubleshooting Chart . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
Precaution for Liquid Gasket . . . . . . . . .....
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . ..
Special Service Tool . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . .
ON-VEHICLE MAINTENANCE . . . . .
ENGINE COOLANT . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
Changing Engine Coolant . . . . . . . . . ...
RADIATOR . . . . . . . . . . . . . . .
Checking Radiator Cap . . . . . . . . . . ...
Checking Radiator . . . . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . .
RADIATOR . . . . . . . . . . . . . . .
Component . . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
COOLING FAN . . . . . . . . . . . . ..
Component (Models with A/C) . . . . . . . . .
Component (Models without A/C) . . . . . . .
Removal and Installation . . . . . . . . . . .
WATER PUMP . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
THERMOSTAT . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
WATER OUTLET . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . ..
COOLING FAN . . . . . . . . . . . . ..
DISASSEMBLY AND ASSEMBLY . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Periodical Maintenance Specification . . . . . ..
Radiator . . . . . . . . . . . . . . . . ...
Thermostat . . . . . . . . . . . . . . . ..
MR18DE
FUNCTION DIAGNOSIS . . . . . . . ..
COOLING SYSTEM . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст