Nissan Tiida C11. Instruction — part 1289
KEY INTERLOCK CABLE
TM-207
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
Remove steering column cover (upper and lower) and instru-
ment lower finisher. Refer to
IP-11, "Removal and Installation"
8.
Pull out the lock plate (A) from the holder (B).
9.
Remove the key interlock cable (1) from the key cylinder (2).
10. Remove the clip (A), and then remove the key interlock cable
(1).
INSTALLATION
CAUTION:
• Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interfer-
ence with adjacent parts.
• After installing key interlock cable to control device assembly, make sure that casing cap and
bracket are firmly secured in their positions.
1.
Place the selector lever in the “P” position.
2.
Turn ignition switch to “ACC” or “ON” position.
3.
Set the key interlock cable (1) to the key cylinder (2).
4.
Install the lock plate (A) to the holder (B).
5.
Turn ignition switch to “LOCK” position.
6.
Temporarily install the adjust holder (A) to the key interlock rod
(B).
7.
Install the casing cap (C) to the cable bracket (D) on the control
device assembly.
CAUTION:
• Do not bend or twist key interlock cable excessively when
installing.
• After installing key interlock cable to cable bracket (D) on
control device assembly, make sure casing cap (C) is
firmly secured in cable bracket (D) on control device
assembly.
• If casing cap (C) is loose [less than 39.2 N (4.0 kg, 8.8 lb)
removing force], replace key interlock cable.
SCIA6976E
SCIA6973E
SCIA6976E
SCIA6188E
TM-208
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
KEY INTERLOCK CABLE
8.
Slide the slider (A) toward the key interlock rod (D) while press-
ing the pull lock (B) down to securely connect the adjust holder
(C) with the key interlock rod (D).
CAUTION:
• Do not press tabs when holding slider (A).
• Do not apply any side to side force to key interlock rod (D)
when sliding slider (A).
9.
Secure the key interlock cable (1) with the clip (A).
10. Install steering column cover (upper and lower) and instrument
lower finisher. Refer to
IP-11, "Removal and Installation"
11. Install the center console assembly. Refer to
12. Install the selector lever knob. Refer to
Knob Removal and Installation"
.
13. Check shift lock system. Refer to
.
SCIA6978E
SCIA6973E
AIR BREATHER HOSE
TM-209
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000001731381
COMPONENTS
REMOVAL
1.
Remove air duct (inlet), air duct and air cleaner case. Refer to
EM-27, "Removal and Installation"
2.
Remove air breather hose.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure air breather hose is not collapsed or blocked due to folding or bending when installed.
NOTE:
• Install the air breather hose (1) to the air breather tube (2) so that
the paint mark (A) faces upward. Also make sure the air breather
hose end laps with air breather tube 17 mm (0.67 in) or more.
• When installing air breather hose (1) to air duct and air cleaner
case, make sure to fully insert the hose clips.
1.
Air cleaner case
2.
Air duct
3.
Air breather hose
4.
Clip
5.
Air breather tube
6.
A/T
WCIA0642E
WCIA0641E
TM-210
< REMOVAL AND INSTALLATION >
[TYPE 1 (4AT: RE4F03B)]
TRANSAXLE ASSEMBLY
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000001731386
Removal and Installation
INFOID:0000000001731383
REMOVAL
1.
Remove the engine and transaxle as an assembly. Refer to
EM-89, "Removal and Installation"
1.
Rear torque rod
2.
Rear engine mounting bracket
3.
A/T fluid charging pipe
4.
A/T fluid level gauge
5.
O-ring
6.
Fluid cooler tube
7.
Copper washer
8.
Bracket
9.
Fluid cooler tube
10. A/T assembly
11.
Rear gusset
12. Engine mounting bracket (LH)
13. Bracket
14. Washer
: Refer to installation.
SCIA8261E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст