Nissan Tiida C11. Instruction — part 1314
ASSEMBLY
TM-307
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
22. Install needle bearing on high clutch hub.
CAUTION:
Be careful with the direction of needle bearing.
23. Remove paper rolled around input shaft assembly (high clutch
drum).
24. Install input shaft assembly (high clutch assembly) (1).
CAUTION:
Align teeth of high clutch drive plates before installing.
25. Install reverse clutch assembly.
CAUTION:
Align teeth of reverse clutch drive plates before installing.
Adjustment (2)
INFOID:0000000001730999
When any parts listed below are replaced, adjust total end play and reverse clutch end play.
TOTAL END PLAY
SAT371D
SCIA7079E
SAT373D
Part name
Total end play
Reverse clutch end play
Transaxle case
●
●
Overrun clutch hub
●
●
Rear internal gear
●
●
Rear planetary carrier
●
●
Rear sun gear
●
●
Front planetary carrier
●
●
Front sun gear
●
●
High clutch hub
●
●
Input shaft assembly (high clutch drum)
●
●
Oil pump cover
●
●
Reverse clutch drum
—
●
TM-308
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
ASSEMBLY
• Measure clearance between reverse clutch drum and needle bear-
ing for oil pump cover.
• Select proper thickness of bearing race so that end play is within
specifications.
1.
Measure dimensions “K” and “L”, and then calculate dimension
“J”.
a.
Measure dimension “K”.
b.
Measure dimension “L”.
c.
Calculate dimension “J”.
2.
Measure dimension “M”.
a.
Place bearing race and needle bearing on oil pump assembly.
SCIA3661E
SCIA3662E
SCIA3663E
“J”:
Distance between oil pump fitting surface of
transaxle case and needle bearing mating sur-
face of input shaft assembly (high clutch drum).
J = K – L
SCIA3664E
SAT378D
ASSEMBLY
TM-309
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
b.
Measure dimension “M”.
c.
Measure thickness of straightedge “t”.
3.
Adjust total end play “T
1
”.
• Select proper thickness of bearing race so that total end play
is within specifications.
REVERSE CLUTCH END PLAY
• Measure clearance between oil pump cover and thrust washer for
reverse clutch drum.
• Select proper thickness of thrust washer so that end play is within
specification.
1.
Measure dimensions “O” and “P”, and then calculate dimension
“N”.
“M”:
Distance between transaxle case fitting surface
of oil pump cover and needle bearing on oil
pump cover.
“M
1
”:
Indication of gauge
SAT379D
M = M
1
– t
T
1
= J – M
Total end play “T
1
”:
SAT443D
SCIA3665E
SCIA3666E
TM-310
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
ASSEMBLY
a.
Place thrust washer on reverse clutch drum.
b.
Measure dimension “O”.
c.
Measure dimension “P”.
d.
Calculate dimension “N”.
2.
Measure dimensions “R” and “S”, and then calculate dimension
“Q”.
a.
Measure dimension “R”.
b.
Measure dimension “S”.
c.
Calculate dimension “Q”.
SCIA3667E
“N”:
Distance between oil pump fitting surface of
transaxle case and thrust washer on reverse
clutch drum.
N = O – P
SCIA3668E
SAT384D
SAT385D
“Q”:
Distance between transaxle case fitting surface
and thrust washer mating surface.
Q = R – S
SAT386D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст