Nissan Tiida C11. Instruction — part 1067
ENGINE MAINTENANCE (HR16DE)
MA-25
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
11. Refill reservoir tank to “MAX” level line with engine coolant.
12. Repeat steps 6 through 11 two or more times with radiator cap installed until engine coolant level no
longer drops.
13. Check cooling system for leaks with engine running.
14. Warm up engine, and check for sound of engine coolant flow while running engine from idle up to 3,000
rpm with heater temperature controller set at several position between “COOL” and “WARM”.
• Sound may be noticeable at heater unit.
15. Repeat step 14 three times.
16. If sound is heard, bleed air from cooling system by repeating steps 6 through 11 until engine coolant level
no longer drops.
FLUSHING COOLING SYSTEM
1.
Install reservoir tank if removed.
2.
Install radiator drain plug.
• If water drain plug on cylinder block is removed, close and tighten it. Refer to
CAUTION:
Be sure to clean radiator drain plug and install with new O-ring. Refer to
3.
Fill radiator and reservoir tank with water and reinstall radiator cap.
4.
Run engine and warm it up to normal operating temperature.
5.
Rev engine two or three times under no-load.
6.
Stop engine and wait until it cools down.
7.
Drain water from the cooling system. Refer to
CO-11, "Changing Engine Coolant"
.
8.
Repeat steps 1 through 7 until clear water begins to drain from radiator.
RADIATOR
RADIATOR : Checking Radiator
INFOID:0000000001730858
Check radiator for mud or clogging. If necessary, clean radiator as follows.
• Be careful not to bend or damage radiator fins.
• When radiator is cleaned without removal, remove all surrounding parts such as cooling fan, radiator shroud
and horns. Then tape harness and connectors to prevent water from entering.
1.
Apply water by hose to the back side of the radiator core vertically downward.
2.
Apply water again to all radiator core surface once per minute.
3.
Stop washing if any stains no longer flow out from radiator.
4.
Blow air into the back side of radiator core vertically downward.
• Use compressed air lower than 490 kPa (4.9 bar, 5 kg/cm
2
, 71 psi) and keep distance more than 30 cm
(11.8 in).
5.
Blow air again into all the radiator core surfaces once per minute until no water sprays out.
FUEL LINES
FUEL LINES : Inspection
INFOID:0000000001277610
Inspect fuel lines, filler cap and tank for improper attachment, leaks,
cracks, damage, loose connections, chafing or deterioration.
If necessary, repair or replace damaged parts.
AIR CLEANER FILTER
SMA803A
MA-26
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE (HR16DE)
AIR CLEANER FILTER : Removal and Installation
INFOID:0000000001730850
REMOVAL
1.
Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2.
Pull up the air cleaner cover (1) and remove it (C).
3.
Remove air cleaner filter (1) and holder (2) assembly from the
air cleaner case.
4.
Remove the air cleaner filter (1) from the holder (2).
INSPECTION AFTER REMOVAL
It is necessary to clean air cleaner filter or replace it at the recommended intervals, more often under dusty
conditions. Refer to
.
• Blow air into the back side of air cleaner filter until no objects spray
out.
INSTALLATION
Installation is in the reverse order of removal.
• Install the air cleaner cover (1) in the direction shown.
ENGINE OIL
PBIC3557J
PBIC3558J
SMA384C
2
: Air cleaner filter
3
: Holder
PBIC3559J
ENGINE MAINTENANCE (HR16DE)
MA-27
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
ENGINE OIL : Draining
INFOID:0000000001730852
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
2.
Stop the engine and wait for 10 minutes.
3.
Loosen oil filler cap.
4.
Remove drain plug and then drain engine oil.
ENGINE OIL : Refilling
INFOID:0000000001730853
1.
Install drain plug with new washer. Refer to
CAUTION:
Be sure to clean drain plug and install with new washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-19, "Fluids and Lubricants"
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
.
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000001730854
REMOVAL
• Using oil filter wrench [SST: KV10115801] (A), remove oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use Genuine NISSAN
Oil Filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any engine
oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter installation surface.
Drain plug
: Refer to
: Vehicle font
PBIC3818E
MA-28
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE (HR16DE)
2.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3.
Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
OIL FILTER : Inspection
INFOID:0000000001730855
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
SPARK PLUG
SPARK PLUG : Removal and Installation
INFOID:0000000001730851
REMOVAL
1.
Remove intake manifold. Refer to
EM-29, "Removal and Installation"
2.
Remove ignition coil. Refer to
EM-47, "Removal and Installation"
.
3.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
SMA010
Oil filter
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA229B
PBIC3871E
Spark plug (Standard type):
Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст