Nissan Tiida C11. Instruction — part 701
EM-156
< ON-VEHICLE REPAIR >
[MR18DE]
INTAKE MANIFOLD
INTAKE MANIFOLD
Component
INFOID:0000000001337785
Removal and Installation
INFOID:0000000001337786
REMOVAL
1.
Remove engine cover (1).
2.
Drain engine coolant. Refer to
.
CAUTION:
Perform this step when engine is cold.
NOTE:
This step is unnecessary when putting plugs to water hoses (to
electronic throttle control actuator)
a.
Disconnect water hoses from electronic throttle control actuator.
b.
Remove electronic throttle control actuator.
CAUTION:
• Handle carefully to avoid any shock to electronic throttle
control actuator.
• Never disassemble.
3.
Remove oil level gauge.
CAUTION:
Cover the oil level gauge guide openings to avoid entry of foreign materials.
1.
PCV hose
2.
Gasket
3.
Intake manifold
4.
Bracket
5.
O-ring
6.
EVAP canister purge volume control
solenoid valve
7.
Water hose
8.
Water hose
9.
Electronic throttle control actuator
10. Gasket
A.
To water outlet
WBIA0771E
WBIA0845E
INTAKE MANIFOLD
EM-157
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4.
Loosen and remove intake manifold (1) bolts (A) (B).
5.
Loosen bolts in reverse order as shown.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
6.
Remove EVAP canister purge volume control solenoid valve
from intake manifold, if necessary.
CAUTION:
Handle it carefully and avoid impacts.
7.
Remove intake manifold.
INSTALLATION
1.
Install intake manifold.
NOTE:
Be sure the intake manifold gasket is seated correctly in groove of intake manifold.
2.
Tighten bolts in numerical order as shown.
: Engine front
PBIC3939E
: Engine front
PBIC3527J
: Engine front
WBIA0788E
EM-158
< ON-VEHICLE REPAIR >
[MR18DE]
INTAKE MANIFOLD
3.
Tighten intake manifold bolt (A). Then tighten intake manifold
bolt (B).
4.
Install electronic throttle control actuator
5.
Install water hoses (3), (5) to electronic throttle control actuator
as shown.
6.
Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
• Check for leaks of engine coolant. Refer to
• Start and warm up the engine. Visually check for engine coolant leaks.
1
: Intake manifold
: Engine front
PBIC3939E
1
: Electronic throttle control actuator
2
: Clamp
4
: Water outlet
A
: Paint Mark
B
: The clamp shall not interfere with the bulged section.
C
: 3 - 7 mm (0.12 - 0.28 in)
AWBIA0115GB
EXHAUST MANIFOLD
EM-159
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
EXHAUST MANIFOLD
Component
INFOID:0000000001337787
Removal and Installation
INFOID:0000000001337788
REMOVAL
1.
Remove exhaust front tube. Refer to
.
2.
Remove exhaust manifold cover.
3.
Remove the heated oxygen sensor 1, using Tool (A).
CAUTION:
Handle it carefully and avoid impacts.
4.
Remove exhaust manifold side bolt of exhaust manifold stay.
1.
Exhaust manifold cover
2.
Exhaust manifold
3.
Gasket
4.
Stud bolt
5.
Bracket
6.
Heated oxygen sensor 1
7.
Exhaust manifold stay
Engine front
WBIA0778E
Tool number
:KV991J0050 (J-44626)
WBIA0772E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст