Nissan Tiida C11. Instruction — part 239
DLK-366
< COMPONENT DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
STEERING LOCK SOLENOID
3.
Check continuity between steering lock solenoid connector and
ground.
Is the inspection result normal?
YES
>>
Check the following.
• Intelligent Key unit ground circuit.
• Intelligent Key unit.
NO
>> Repair or replace harness between steering lock solenoid and Intelligent Key unit.
A
B
Continuity
Intelligent Key unit
connector
Terminal
Steering lock sole-
noid connector
Terminal
M52
31
M6
4
Yes
A
Ground
Continuity
Intelligent Key unit connector
Terminal
M52
31
No
PIIB6637E
KEY INTERLOCK SOLENOID (M/T)
DLK-367
< COMPONENT DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY INTERLOCK SOLENOID (M/T)
Diagnosis Procedure
INFOID:0000000001530366
1.
CHECK INTERLOCK SOLENOID POWER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key unit and key switch and ignition knob switch connector.
3.
Check continuity between Intelligent Key unit connector M52 (A) terminal 22 and key switch and ignition
knob switch connector M32 (B) terminal 5.
4.
Check continuity between Intelligent Key unit connector (A) ter-
minal 22 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness between Intelligent Key unit and key switch and ignition knob switch.
2.
CHECK INTERLOCK SOLENOID GROUND CIRCUIT
Check continuity between key switch and ignition knob switch con-
nector M32 terminal 6 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK INTELLIGENT KEY SOLENOID RESISTANCE
Check resistance between key switch and ignition knob switch termi-
nals 5 and 6.
OK or NG
OK
>> Key switch and ignition knob switch is OK.
NG
>> Replace key switch and ignition knob switch.
A
B
Continuity
Intelligent Key unit
connector
Terminal
Key switch and ig-
nition knob switch
connector
Terminal
M52
22
M32
5
Yes
A
Ground
Continuity
Intelligent Key unit connector
Terminal
M52
22
No
ALKIA0786ZZ
Key switch and ignition knob
switch connector
Terminal
Ground
Continuity
M32
6
Yes
ALKIA0787ZZ
Key switch and ignition knob
switch
Terminal
Terminal
Resistance
5
6
1-10
Ω
WIIA1301E
DLK-368
< COMPONENT DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
STOP LAMP SWITCH (A/T)
STOP LAMP SWITCH (A/T)
Diagnosis Procedure
INFOID:0000000001530367
1.
CHECK STOP LAMP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key unit connector.
3.
Check voltage between Intelligent Key unit harness connector
M52 terminal 26 and ground.
Is the inspection result normal?
YES
>> Stop lamp switch is OK.
NO
>> GO TO 2.
2.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
Disconnect stop lamp switch connector.
2.
Check voltage between stop lamp switch harness connector
E13 terminal 1 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness between stop lamp switch
power supply circuit and fuse.
3.
CHECK STOP LAMP SWITCH OPERATION
Check continuity between stop lamp switch terminals 1 and 2.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace stop lamp switch.
4.
CHECK STOP LAMP SWITCH CIRCUIT
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M52
26
Ground
Brake pedal
depressed
Battery volt-
age
Brake pedal
released
0
WIIA1207E
1 - Ground
: Battery voltage
WIIA1255E
Component
Terminals
Condition
Continuity
Stop lamp
switch
1
2
Brake pedal depressed
Yes
Brake pedal released
No
WIIA1256E
STOP LAMP SWITCH (A/T)
DLK-369
< COMPONENT DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Check continuity between Intelligent Key unit harness connector
(A) M52 terminal 26 and stop lamp switch harness connector (B)
E13 terminal 2.
2.
Check continuity between Intelligent Key unit harness connector
M52 terminal 26 and ground.
Is the inspection result normal?
YES
>> Check condition of harness and connector.
NO
>> Repair or replace harness.
26 - 2
: Continuity should exist.
26 - Ground
: Continuity should not exist.
WIIA1257E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст