Nissan Tiida C11. Instruction — part 1295
DISASSEMBLY
TM-231
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
35. Remove front sun gear from front planetary carrier.
36. Remove needle bearing (1) from front sun gear (2).
• Inspect needle bearing (1) and front sun gear (2), and
replace if damaged or worn.
37. Remove front planetary carrier and low one-way clutch according to the following procedures.
a.
Remove snap ring using suitable tool.
b.
Remove low one-way clutch (1) and front planetary carrier (2) as
a set from transaxle case.
SAT368D
SCIA6960E
SCIA3633E
SCIA5896J
TM-232
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
DISASSEMBLY
c.
Check that low one-way clutch rotates counter-clockwise around
front planetary carrier. Then try to turn it clockwise and check
that it is locked.
• Replace low one-way clutch if necessary.
d.
Remove low one-way clutch from front planetary carrier by turn-
ing it in the direction of unlock.
• Inspect low one-way clutch, and replace if damaged or
worn.
e.
Remove needle bearing (1) from front planetary carrier (2).
• Inspect needle bearing (1) and front planetary carrier (2),
and replace if damaged or worn.
f.
Check clearance between pinion washer and front planetary
carrier using feeler gauge.
• Replace front planetary carrier if the clearance exceeds
allowable limit.
38. Remove rear planetary carrier and rear sun gear according to the following procedures.
a.
Remove rear planetary carrier (with rear sun gear) from tran-
saxle case.
SAT048D
SCIA6047J
Standard clearance and allowable limit:
.
SAT050D
SAT051D
DISASSEMBLY
TM-233
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
b.
Remove rear sun gear from rear planetary carrier.
• Inspect rear sun gear, and replace if damaged or worn.
c.
Remove needle bearing (1) from rear planetary carrier (2).
• Inspect needle bearing (1) and rear planetary carrier (2),
and replace if damaged or worn.
d.
Check clearance between pinion washer and rear planetary car-
rier using feeler gauge.
• Replace rear planetary carrier if the clearance exceeds
allowable limit.
39. Remove rear internal gear (1) and forward clutch hub (2) as a
set from forward clutch drum.
40. Remove needle bearing (1) from rear internal gear (2).
• Inspect needle bearing (1), and replace if damaged or
worn.
SAT052D
SCIA5927J
Standard clearance and allowable limit:
.
SAT054D
SCIA5897J
SCIA6041J
TM-234
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
DISASSEMBLY
41. Remove overrun clutch hub (1) from forward clutch drum.
42. Remove thrust washer (1) from overrun clutch hub (2).
• Inspect thrust washer (1) and overrun clutch hub (2), and
replace if damaged or worn.
43. Remove forward clutch assembly and overrun clutch assembly
(1) from transaxle case.
44. Remove needle bearing (1) and thrust washer (2) from bearing
retainer.
• Inspect needle bearing (1) and thrust washer (2), and
replace damaged or worn.
45. Remove side cover fitting bolts (1), and then remove side cover
by lightly tapping it using a soft hammer.
CAUTION:
Do not damage side cover.
46. Remove side cover gasket from side cover.
SCIA5898J
SCIA5899J
SCIA5900J
SCIA5901J
SCIA6039J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст