Nissan Tiida C11. Instruction — part 553
EC-862
< COMPONENT DIAGNOSIS >
[MR18DE]
P0335 CKP SENSOR (POS)
P0335 CKP SENSOR (POS)
Description
INFOID:0000000001161829
The crankshaft position sensor (POS) is located on the oil pan facing
the gear teeth (cogs) of the signal plate. It detects the fluctuation of
the engine revolution.
The sensor consists of a permanent magnet and Hall IC.
When the engine is running, the high and low parts of the teeth
cause the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor
changes.
The ECM receives the voltage signal and detects the fluctuation of
the engine revolution.
ECM receives the signals as shown in the figure.
DTC Logic
INFOID:0000000001161830
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5V with igni-
tion switch ON.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
PBIA9209J
JMBIA0714GB
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0335
Crankshaft position sen-
sor (POS) circuit
• The crankshaft position sensor (POS) signal
is not detected by the ECM during the first
few seconds of engine cranking.
• The proper pulse signal from the crankshaft
position sensor (POS) is not sent to ECM
while the engine is running.
• The crankshaft position sensor (POS) signal
is not in the normal pattern during engine run-
ning.
• Harness or connectors
[Crankshaft position sensor (POS) circuit
is open or shorted.]
(Refrigerant pressure sensor circuit is
shorted.)
(Accelerator pedal position sensor 2 cir-
cuit is shorted.)
• Crankshaft position sensor (POS)
• Refrigerant pressure sensor
• Accelerator pedal position sensor (APPS
2)
• Signal plate
P0335 CKP SENSOR (POS)
EC-863
< COMPONENT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001161831
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E15. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY CIRCUIT-I
1.
Disconnect crankshaft position (CKP) sensor (POS) harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between CKP sensor (POS) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 3.
3.
CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit.
4.
CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY CIRCUIT-III
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair short to ground or short to power in harness or connectors.
5.
CHECK REFRIGRANT PRESSURE SENSOR
.
CKP sensor (POS)
Ground
Voltage
Connector
Terminal
F15
1
Ground
Approx. 5V
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F15
1
F11
75
Existed
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F11
74
Refrigerant pressure sensor
E17
3
75
CKP sensor (POS)
F15
1
E16
102
APP sensor 2
E12 (LHD models)
M204 (RHD models)
5
EC-864
< COMPONENT DIAGNOSIS >
[MR18DE]
P0335 CKP SENSOR (POS)
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace refrigrant pressure sensor.
6.
CHECK APP SENSOR
EC-955, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> GO TO 7.
7.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
Go to
EC-693, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Require-
>> INSPECTION END
8.
CHECK CKP SENSOR (POS) GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK CKP SENSOR (POS) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
10.
CHECK CRANKSHAFT POSITION SENSOR (POS)
EC-865, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Replace crankshaft position sensor (POS).
11.
CHECK GEAR TOOTH
Visually check for chipping signal plate gear tooth.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Replace the signal plate.
12.
CHECK INTERMITTENT INCIDENT
GI-55, "Intermittent Incident"
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F15
2
F11
62
Existed
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F15
3
F11
61
Existed
P0335 CKP SENSOR (POS)
EC-865
< COMPONENT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
>> INSPECTION END
Component Inspection
INFOID:0000000001161832
1.
CHECK CRANKSHAFT POSITION SENSOR (POS)-I
1.
Turn ignition switch OFF.
2.
Loosen the fixing bolt of the sensor.
3.
Disconnect crankshaft position sensor (POS) harness connector.
4.
Remove the sensor.
5.
Visually check the sensor for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace crankshaft position sensor (POS).
2.
CHECK CRANKSHAFT POSITION SENSOR (POS)-II
Check resistance between crankshaft position sensor (POS) terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace crankshaft position sensor (POS).
PBIA9209J
Terminals (Polarity)
Resistance [at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0 or
∞
Ω
1 (+) - 3 (-)
2 (+) - 3 (-)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст