Nissan Tiida C11. Instruction — part 1286
PARK/NEUTRAL POSITION (PNP) SWITCH
TM-195
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PARK/NEUTRAL POSITION (PNP) SWITCH
Park/Neutral Position (PNP) Switch
INFOID:0000000001733159
COMPONENTS
REMOVAL
1.
Remove the air duct. Refer to
EM-27, "Removal and Installation"
.
2.
Disconnect the PNP switch connector.
3.
Disconnect the control cable from the PNP switch.
4.
Remove the PNP switch bolts and the PNP switch.
INSTALLATION
Installation is in the reverse order of removal.
• Align PNP switch position when installing.
• After installation is completed, check and adjust A/T position. Refer to
TM-204, "Checking of A/T Position"
TM-204, "Adjustment of A/T Position"
.
• After installation is completed, check continuity of PNP switch. Refer to
.
PARK/NEUTRAL POSITION (PNP) SWITCH ADJUSTMENT
1.
Set selector lever and instruction shaft (1) in “N” position.
2.
Remove the air duct. Refer to
EM-27, "Removal and Installation"
.
3.
Remove control cable from instruction shaft (1).
4.
Loosen PNP switch bolts.
: Bolt
5.
Insert the pin (3) [4 mm (0.16 in) dia.] straight into instruction shaft
(1) adjustment hole.
6.
Rotate PNP switch (2) until the pin (3) can also be inserted
straight into hole in PNP switch (2).
7.
Tighten PNP switch bolts to the specified torque.
8.
Remove the pin (3) from adjustment hole after adjusting PNP
switch (2).
9.
Check continuity of PNP switch (2). Refer to
10. Adjust and check A/T position. Refer to
TM-204, "Checking of A/T Position"
.
1.
A/T
2.
PNP switch
SCIA6204J
SCIA6218J
TM-196
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
PARK/NEUTRAL POSITION (PNP) SWITCH
11. Reinstall any parts removed.
REVOLUTION SENSOR
TM-197
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REVOLUTION SENSOR
Revolution Sensor
INFOID:0000000001733160
COMPONENTS
REMOVAL
Refer to the figure for revolution sensor removal procedure.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Ensure revolution sensor harness is firmly secured with bolt.
(1): Revolution sensor
: Bolt
Turbine Revolution Sensor (Power Train Revolution Sensor)
INFOID:0000000001733161
COMPONENTS
1.
A/T
2.
Revolution sensor
SCIA6205J
SCIA6518J
TM-198
< ON-VEHICLE REPAIR >
[TYPE 1 (4AT: RE4F03B)]
REVOLUTION SENSOR
REMOVAL
Refer to the figure for turbine revolution sensor (power train revolution sensor) removal procedure.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
After installing control cable, check and adjust A/T position. Refer to
TM-204, "Checking of A/T Position"
TM-204, "Adjustment of A/T Position"
.
1.
A/T
2.
O-ring
3.
Turbine revolution sensor (power
train revolution sensor)
SCIA6207J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст