Nissan Tiida C11. Instruction — part 216
DLK-274
< FUNCTION DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
HAZARD AND BUZZER REMINDER FUNCTION
Component Description
INFOID:0000000001396709
*: Sedan only
Item
Function
BCM
Controls the hazard and buzzer reminder function with Intelligent Key unit.
Intelligent Key unit
Controls the hazard and buzzer reminder function with BCM.
Combination meter
Turns ON the LOCK indicator, KEY indicator, turn signal indicator and buzzer
(built in combination meter) by the request from Intelligent Key unit via CAN com-
munication.
Intelligent Key warning buzzer (driver side)
Sounds by the request signal from Intelligent Key unit via CAN communication.
Intelligent Key warning buzzer (trunk)
*
Sounds by the request signal from Intelligent Key unit via CAN communication.
DIAGNOSIS SYSTEM (BCM)
DLK-275
< FUNCTION DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000001396710
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)
INFOID:0000000001396711
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM. Refer to
XX-XX, "*****"
.
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION
The BCM part number is displayed.
CONFIGURATION
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
—
BCM
×
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioner
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
Combination switch
COMB SW
×
Immobilizer
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
PTC heater system
PTC HEATER
×
×
DLK-276
< FUNCTION DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
INTELLIGENT KEY
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor Item
Condition
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
PUSH SW
Indicates [ON/OFF] condition of ignition knob switch.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
CDL LOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW
Indicates [ON/OFF] condition of back door switch.
BACK DOOR OPNR SW
Indicates [ON/OFF] condition of back door opener switch.
I-KEY LOCK
Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I-KEY UNLOCK
Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
UNLOCK WITH DR
This item is indicated, but not monitored.
UNLOCK SHOCK
Indicates [ON/OFF] condition of signal from air bag diagnosis unit.
• ON: During the unlock operation interlock with air bag.
• OFF: Other than above.
SHOCK SENSOR
Indicates [NOMAL/ON/OFF] condition of circuit between BCM and air bag diagnosis sen-
sor unit.
• NORMAL: Ignition switch ON. (BCM is receiving normal condition signal from air bag di-
agnosis sensor unit.)
• ON: During the receiving of air bag deployment signal from air bag diagnosis sensor
unit.
• OFF: After the receiving of air bag deployment signal from air bag diagnosis sensor unit.
VEHICLE SPEED
Displays the vehicle speed signal received from combination meter by numerical value
[km/h].
Test item
Description
SUPER LOCK
This test is able to check super lock operation [LOCK (SET)/UNLOCK (RELEASE)].
DOOR LOCK IND
This test is able to check door lock indicator (built in door lock and unlock switch on center
console) operation [ON/OFF].
DOOR LOCK
This test is able to check door lock operation [ALL LOCK/ALL UNLOCK/DR UNLOCK/
OTHER UNLOCK].
Test item
Description
SECURITY DOOR LOCK SET
Anti hijack function mode can be changed in this mode.
• ON: Anti hijack mode is active.
• OFF: Anti hijack mode is inactive.
DIAGNOSIS SYSTEM (BCM)
DLK-277
< FUNCTION DIAGNOSIS >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000001396712
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)
INFOID:0000000001396713
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
ACTIVE TEST
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
Monitor Item
Condition
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
PUSH SW
Indicates [ON/OFF] condition of ignition knob switch.
I-KEY LOCK
Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I-KEY UNLOCK
Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from Intelligent Key unit.
Monitor Item
Condition
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
PUSH SW
Indicates [ON/OFF] condition of ignition knob switch.
TRNK OPNR SW
Indicates [ON/OFF] condition of back door opener switch.
VEHICLE SPEED
Displays the vehicle speed signal received from combination meter by numerical value
[km/h].
Test item
Description
TRUNK/GLASS HATCH
This test is able to check back door/trunk opener operation [ON/OFF].
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст