Nissan Tiida C11. Instruction — part 1404
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
TM-667
< SYMPTOM DIAGNOSIS >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000001381628
Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.
Reference page
SUSPECTED PARTS
(Possible cause)
OIL (Oi
l
le
v
e
l is
lo
w
.)
OIL (W
ro
ng
oi
l.)
OIL (Oi
l
le
v
e
l is
hi
gh
.)
GASKET (Damaged)
OIL SEAL (W
orn or
damaged)
O-R
ING
(W
orn
o
r
da
ma
ge
d)
SHIFT
CONT
ROL
L
INKAGE (W
orn
)
SHIFT
FORK (W
orn
)
GEAR (W
orn
or
da
ma
ge
d)
BEARING (W
orn or damaged)
BAULK
RING (W
orn
or
da
ma
ge
d)
INSER
T SPRING (Damaged)
Symptoms
Noise
1
2
3
3
Oil leakage
3
1
2
2
2
Hard to shift or will not shift
1
1
2
3
3
Jumps out of gear
1
2
2
TM-668
< PRECAUTION >
[6MT: RS6F94R]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Service Notice or Precautions for Instruction Transaxle
INFOID:0000000001381629
CAUTION:
• If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Return CSC insert to original position to remove transaxle assembly. Dust on clutch disc sliding
parts may damage seal of CSC and may cause clutch fluid leakage.
• Never reuse transaxle gear oil, once it has been drained.
• Check oil level or replace gear oil with vehicle on level surface.
• During removal or installation, keep inside of transaxle clear of dust or dirt.
• Check for the correct installation status prior to removal or disassembly. If matching marks are
required, be certain they do not interfere with the function of the parts they are applied.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to out-
side. If tightening sequence is specified, use it.
• Never damage sliding surfaces and mating surfaces.
PREPARATION
TM-669
< PREPARATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000001381630
Tool number
Tool name
Description
KV381054S0
Puller
Removing mainshaft front bearing outer race
KV38100200
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
• Installing mainshaft front bearing outer race
• Installing mainshaft rear bearing outer race
• Installing differential side bearing outer race
(clutch housing side)
ST33220000
Drift
a: 37 mm (1.46 in) dia.
b: 31 mm (1.22 in) dia.
c: 22 mm (0.87 in) dia.
Installing input shaft oil seal
ST33400001
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
Installing differential side bearing outer race
(transaxle case side)
KV38100300
Drift
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.
Installing differential side oil seal
ST36720030
Drift
a: 70 mm (2.76 in) dia.
b: 40 mm (1.57 in) dia.
c: 29 mm (1.14 in) dia.
• Installing input shaft rear bearing
• Installing mainshaft front bearing inner race
ZZA0601D
ZZA1143D
ZZA1046D
ZZA0814D
ZZA1046D
ZZA0978D
TM-670
< PREPARATION >
[6MT: RS6F94R]
PREPARATION
Commercial Service Tools
INFOID:0000000001381631
ST33052000
Drift
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
• Removing mainshaft rear bearing inner race
• Removing 6th main gear
• Removing 5th main gear
• Removing 4th main gear
• Removing 1st main gear
• Removing 1st-2nd synchronizer assembly
• Removing 2nd main gear
• Removing bushing
• Removing 3rd main gear
• Removing mainshaft front bearing inner
race
KV32102700
Drift
a: 54 mm (2.13 in) dia.
b: 32 mm (1.26 in) dia.
• Installing bushing
• Installing 2nd main gear
• Installing 3rd main gear
• Installing 4th main gear
• Installing 5th main gear
• Installing 6th main gear
ST30901000
Drift
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.
Installing mainshaft rear bearing inner race
ST33061000
Drift
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
Removing differential side bearing inner race
(clutch housing side)
Tool number
Tool name
Description
ZZA0969D
S-NT065
ZZA0978D
ZZA0969D
Tool name
Description
Socket
a: 8 mm (0.31 in)
b: 5 mm (0.20 in)
Removing and installing drain plug
Spacer
a: 25 mm (0.98 in) dia.
b: 25 mm (0.98 in)
Removing mainshaft front bearing outer race
PCIB1776E
PCIB1780E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст