Nissan Tiida C11. Instruction — part 297
DLK-598
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY & SUPER LOCK]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Removal and Installation of Fuel Filler Lid Opener
INFOID:0000000001732043
REMOVAL
1.
Remove trunk side finisher (RH). Refer to
XX-XX, "*****"
.
2.
Remove fuel filler lid opener cable lock ring.
3.
Remove front and rear kicking plates. Refer to
XX-XX, "*****"
.
4.
Remove rear cushion assembly. Refer to
XX-XX, "*****"
.
5.
Remove the bolts and the fuel filler lid opener handle.
6.
Remove fuel filler lid opener cable clips from the vehicle.
7.
Remove the fuel filler lid opener cable (LH drive).
8.
Remove the fuel filler lid opener cable (RH drive).
PIIB3831J
LIIA2670E
LIIA2629E
ALKIA0651GB
FUEL FILLER LID OPENER
DLK-599
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
DLK-600
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY & SUPER LOCK]
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Parts Location
INFOID:0000000001732044
Removal and Installation
INFOID:0000000001732045
REMOVAL
1.
Remove front door finisher. Refer to
XX-XX, "*****"
.
2.
Fully close front door window.
3.
Remove the front door sealing screen.
NOTE:
If sealing screen is reused, cut butyl tape in a way that leaves it on the sealing screen.
4.
Remove front door rear glass run channel. Refer to
XX-XX, "*****"
.
5.
Remove the cables from the holder.
6.
Remove inside handle bolt, and slide the handle toward the rear
of the vehicle. disengage the handle from the door panel, and
remove the inside handle.
7.
Disengage the handle from the door panel, and remove the inside handle.
1.
Front door
2.
Inside handle
3.
Inside handle cable
4.
Door lock assembly
5.
Outside handle cable
6.
TORX bolt (T30)
7.
Key cylinder connecting rod
8.
Grommet
9.
TORX bolt (T30)
10. Rear gasket
11. Door key cylinder assembly
(Driver's side)
Outside handle escutcheon
(passenger's side)
12. Outside handle
13. Front gasket
14. Lock knob cable
15. Holder
16. Outside handle bracket
PIIB6523E
PIIB6524E
FRONT DOOR LOCK
DLK-601
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Disconnect the inside handle cable and lock knob cable from the
inside handle.
CAUTION:
During removal and installation, work so as not to bend the
ends of the lock knob cable and inside handle cable.
9.
Remove the door side grommet, and the door key cylinder
assembly (escutcheon) bolt.
10. Remove the key cylinder connecting rod (key cylinder side).
11. If equipped, disconnect the door antenna, the door request
switch connector and remove the harness clamp. (Vehicle with
intelligent key systems only).
12. Remove the door cylinder assembly while pulling the outside
handle forward.
13. Pull the outside door handle forward and then slide it toward the
rear of the vehicle to remove.
14. Remove the front and rear gaskets.
PIIB6525E
PIIB5808E
PIIB5809E
PIIB5810E
PIIB6526E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст