Nissan Tiida C11. Instruction — part 259
DLK-446
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
HOOD
5.
Remove hood opener on bottom left of instrument panel, and
then remove hood lock cable.
6.
Remove grommet on lower dashboard, and pull out hood lock
cable from passenger room side.
CAUTION:
While pulling the cable, be careful not to damage (peel)
hood opener cable outer surface on edges of body through
hole.
INSTALLATION
Installation is in the reverse order of removal.
• Perform hood fitting adjustment. Refer to
Hood Lock Reinforcement
When installing hood lock reinforcement, loosen hood bolts, and
then tighten bolts in the order as shown.
Hood Lock Cable
1.
Pull the hood lock cable through the panel hole to the engine compartment.
CAUTION:
Be careful not to bend the cable too much, keeping the
radius 100 mm (3.94 in) or more.
2.
Check that the cable is not offset from the positioning grommet,
and push the grommet into the panel hole securely.
3.
Apply the sealant around the grommet (at * mark).
4.
Install cable securely to lock.
5.
After installing, check hood lock adjustment and hood opener
operation.
Hood Lock Control Inspection
INFOID:0000000001732020
CAUTION:
If the hood lock cable is bent or deformed, replace it.
LIIA2667E
23.6 N·m (2.4 kg-m, 17 ft-lb)
PIIB6513E
PIIB5801E
PIIB6537E
HOOD
DLK-447
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Check that the secondary latch is properly engaged with the secondary striker (B: 6.8 mm (0.268 in) with
hood's own weight.
2.
While operating the hood release handle, carefully check that the front end of the hood is raised by
approx. 20 mm (0.79 in). Also check that the hood release handle returns to the original position.
3.
Check that the secondary hood release operates at 29.4 N (3.0 kg) or below.
4.
Confirm static closing force of the hood is 343 – 441 N·m (35 – 44 kg-m).
5.
Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points as shown.
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
PIIB5794E
PIIB6514E
DLK-448
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Removal and Installation
INFOID:0000000001732021
REMOVAL
Radiator Core Support Upper
1.
Remove the air duct. Refer to
EM-27, "Removal and Installation"
(MR18DE), or
EM-269, "Removal and Installation"
(K9K).
2.
Remove the headlamp (LH/RH). Refer to
EXL-84, "Removal and Installation"
3.
Remove the hood lock assembly, and remove hood lock cable. Refer to
4.
Remove the air guide and hood lock cable clip.
5.
Remove the washer tank inlet. Refer to
WW-64, "Removal and Installation"
.
6.
Remove the radiator core support upper.
Radiator Core Support Lower
1.
Remove the air duct. Refer to
EM-27, "Removal and Installation"
(MR18DE), or
EM-269, "Removal and Installation"
(K9K).
2.
Remove the front bumper. Refer to
EXT-13, "Removal and Installation"
.
3.
Remove the headlamp (LH/RH). Refer to
EXL-84, "Removal and Installation"
4.
Remove the hood lock assembly, and remove hood lock cable. Refer to
5.
Remove the air guide and hood lock cable mounting clip.
6.
Remove the front bumper reinforcement. Refer to
EXT-13, "Removal and Installation"
.
7.
Remove the radiator core lower stay.
8.
Remove the undercover.
PIIB6515E
1.
Radiator core support upper
2.
Radiator core support lower
3.
Radiator core support lower stay
4.
Radiator core support side stay
5.
Air guide
24.5 N·m (2.5 kg-m, 18 ft-lb)
RADIATOR CORE SUPPORT
DLK-449
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
9.
Remove radiator core support lower side stay.
10. Tie a cord to all radiator core upper supports of the radiator and
condenser.
NOTE:
To prevent the compressor and radiator from being dropped
when the radiator core lower support is removed.
11. Remove the bolts, and lower radiator core lower supports.
12. Remove the radiator core lower supports.
INSTALLATION
Installation is in the reverse order of removal.
55.0 N·m (5.6 kg-m, 41 ft-lb)
PIIB2800J
PIIB2799J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст