Nissan Tiida C11. Instruction — part 1327
VEHICLE SPEED SENSOR MTR
TM-359
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
VEHICLE SPEED SENSOR MTR
Description
INFOID:0000000001712989
The vehicle speed sensor·MTR is built into the speedometer assembly. The sensor functions as an auxiliary
device to the revolution sensor when it is malfunctioning. The TCM will then use a signal sent from the vehicle
speed sensor·MTR.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000001712990
Remarks: Specification data are reference values.
On Board Diagnosis Logic
INFOID:0000000001712991
Diagnostic trouble code “VHCL SPEED SEN-MTR” with CONSULT-III or 2nd judgement flicker without CON-
SULT-III is detected when TCM does not receive the proper voltage signal from the sensor.
Possible Cause
INFOID:0000000001712992
• Harness or connector
(Sensor circuit is open or shorted.)
• Vehicle speed sensor
DTC Confirmation Procedure
INFOID:0000000001712993
CAUTION:
• Always drive vehicle at a safe speed.
• If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1.
Turn ignition switch ON and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
2.
Touch “START”.
3.
Start engine and accelerate vehicle from 0 to 25 km/h (0 to 16 MPH).
4.
If the check result is NG, go to
WITHOUT CONSULT-III
1.
Start engine.
2.
Drive vehicle under the following conditions:
Selector lever position: “D” position
Vehicle speed: Higher than 25 km/h (16 MPH)
3.
Perform self-diagnosis. Refer to
TM-38, "Diagnosis Procedure without CONSULT-III"
4.
If the check result is NG, go to
Diagnosis Procedure
INFOID:0000000001712995
1.
CHECK INPUT SIGNAL
With CONSULT-III
1.
Start engine.
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3.
Read out the value of “VHCL/S SE-MTR” while driving.
Check the value changes according to driving speed.
Item name
Condition
Display value
VHCL/S SE-MTR
During driving
Approximately matches the speedometer reading.
Item name
Condition
Display value
VHCL/S SE-MTR
During driving
Approximately matches
the speedometer reading.
TM-360
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
VEHICLE SPEED SENSOR MTR
Without CONSULT-III
1.
Start engine.
2.
Check voltage between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Combination meter. Refer to
MWI-4, "METER SYSTEM : System Description"
.
• Harness for short or open between TCM and combination meter.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
CHECK DTC
Perform
TM-359, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 4.
4.
CHECK TCM
1.
Check TCM input/output signals. Refer to
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Item
Connec-
tor
Terminal
Condition
Judgement
standard (Ap-
prox.)
Vehicle
speed sen-
sor
E32
40 -
Ground
When driving vehicle at 2
to 3 km/h (1 to 2 MPH)
for 1 m (3 ft) or more.
Voltage varies
between less
than 0V and
more than 4.5V
SCIA4940E
SHIFT SOLENOID VALVE A
TM-361
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT SOLENOID VALVE A
Description
INFOID:0000000001713002
Shift solenoid valves A and B are turned ON or OFF by the TCM in response to signals sent from the PNP
switch, vehicle speed and ECM (throttle opening). Gears will then be shifted to the optimum position.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000001713003
Remarks: Specification data are reference values.
On Board Diagnosis Logic
INFOID:0000000001713004
Diagnostic trouble code “SHIFT SOLENOID/V A” with CONSULT-III or 4th judgement flicker without CON-
SULT-III is detected when TCM detects an improper voltage drop when it tries to operate the solenoid valve.
Possible Cause
INFOID:0000000001713005
• Harness or connector
(Solenoid circuit is open or shorted.)
• Shift solenoid valve A
DTC Confirmation Procedure
INFOID:0000000001713006
CAUTION:
• Always drive vehicle at a safe speed.
• If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1.
Turn ignition switch ON and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
2.
Touch “START”.
3.
Start engine.
4.
Drive vehicle in “D” position and allow the transaxle to shift 1
→
2 (“GEAR”).
5.
If the check result is NG, go to
WITHOUT CONSULT-III
1.
Start engine.
2.
Drive vehicle in D
1
→
D
2
position.
3.
Perform self-diagnosis. Refer to
TM-38, "Diagnosis Procedure without CONSULT-III"
4.
If the check result is NG, go to
Diagnosis Procedure
INFOID:0000000001713008
1.
CHECK INPUT SIGNAL
With CONSULT-III
1.
Start engine.
2.
Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3.
Read out the value of “SHIFT S/V A” while driving.
Check the value changes according to driving speed.
Gear position
1
2
3
4
Shift solenoid valve A
ON (Closed)
OFF (Open)
OFF (Open)
ON (Closed)
Shift solenoid valve B
ON (Closed)
ON (Closed)
OFF (Open)
OFF (Open)
Item name
Condition
Display value
SHIFT S/V A
When shift solenoid valve A operates.
(When driving in “D
1
” or “D
4
”.)
ON
When shift solenoid valve A does not operate.
(When driving in “D
2
” or “D
3
”.)
OFF
TM-362
< COMPONENT DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
SHIFT SOLENOID VALVE A
Without CONSULT-III
1.
Start engine.
2.
Check voltage between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK SHIFT SOLENOID VALVE A CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check resistance between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 3.
3.
CHECK HARNESS BETWEEN TCM AND TERMINAL CORD ASSEMBLY HARNESS CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly harness connector and TCM connector.
3.
Check continuity between terminal cord assembly harness con-
nector terminal and TCM connector terminal.
4.
If OK, check harness for short to ground and short to power.
5.
If OK, check continuity between ground and transaxle assembly.
6.
Reinstall any part removed.
OK or NG
Item name
Condition
Display value
SHIFT S/V A
When shift solenoid valve A operates.
(When driving in “D
1
” or “D
4
”.)
ON
When shift solenoid valve A does not oper-
ate.
(When driving in “D
2
” or “D
3
”.)
OFF
Item
Connec-
tor
Terminal
Condition
Judgement
standard (Ap-
prox.)
Shift sole-
noid valve A
E31
11 - Ground
When shift solenoid
valve A operates.
(When driving in “D
1
” or
“D
4
”.)
Battery volt-
age
When shift solenoid
valve A does not oper-
ate.
(When driving in “D
2
” or
“D
3
”.)
0V
SCIA3248E
Solenoid Valve
Connector
Terminal
Resistance (Ap-
prox.)
Shift solenoid valve A
E31
11 - Ground
20 - 30
Ω
SCIA3249E
Item
Connector
Terminal
Continuity
TCM
E31
11
Yes
Terminal cord assembly
harness connector
F30
2
SCIA3250E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст