Nissan Sentra. Instruction — part 609
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1. Move front seat to the full forward position.
2. Lift up front end lower of front kicking plate inner while pulling
toward inside of the vehicle and release front kicking plate inner
pawls as shown.
: Pawl
3. Begin at the front and release front kicking plate inner pawls as
shown.
: Pawl
4. Lift up rear end lower of front kicking plate inner while pulling
toward inside of the vehicle and release front kicking plate inner
pawls as shown, then remove front kicking plate inner.
: Pawl
Installation
Installation is in the reverse order of removal.
REAR
Removal
1. Lift up front end lower of rear kicking plate inner while pulling
toward inside of the vehicle and release rear kicking plate inner
pawls as shown.
: Pawl
JMJIA6486ZZ
JMJIA6487ZZ
JMJIA6488ZZ
JMJIA6489ZZ
INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Begin at the front and release rear kicking plate inner pawls as
shown.
: Pawl
3. Lift up rear end lower of rear kicking plate inner while pulling
toward inside of the vehicle and release rear kicking plate inner
pawls as shown then remove rear kicking plate inner.
: Pawl
Installation
Installation is in the reverse order of removal.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000009756910
REMOVAL
1. Remove front kicking plate inner. Refer to
INT-24, "KICKING PLATE INNER : Removal and Installation"
2. Remove dash side finisher
a. Remove dash side finisher clip (A).
b. Pull back dash side finisher as shown to release dash side fin-
isher pawls and remove.
: Pawl
JMJIA6490ZZ
JMJIA6491ZZ
JMJIA6492ZZ
JMJIA6493ZZ
BODY SIDE TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000009756911
FRONT
Removal
1. Remove dash side finisher. Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
.
2. Remove front body side welt.
CAUTION:
Use care not to stretch out welt if it is to be reused.
Installation
Installation is in the reverse order of removal.
REAR
Removal
1. Remove rear kicking plate inner. Refer to
INT-24, "KICKING PLATE INNER : Removal and Installation"
.
2. Remove rear body side welt.
CAUTION:
Use care not to stretch out welt if it is to be reused.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
CENTER PILLAR LOWER FINISHER : Removal and Installation
INFOID:0000000009756912
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Do not damage the body panel.
REMOVAL
1. Move front seat to the full forward position.
2. Remove front and rear body side welts. Refer to
INT-27, "BODY SIDE WELT : Removal and Installation"
3. Remove center pillar lower finisher.
a. Release center pillar lower finisher clips using a suitable tool (A).
: Clip
JMJIA6494ZZ
INT-28
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
b. Release center pillar lower finisher pawls as shown and remove.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing, check that clips are accurately aligned with the holes on body panel, then press in.
CENTER PILLAR UPPER FINISHER
CENTER PILLAR UPPER FINISHER : Removal and Installation
INFOID:0000000009756913
REMOVAL
1. Remove center pillar lower finisher. Refer to
INT-27, "CENTER PILLAR LOWER FINISHER : Removal
2. Remove front seat belt D-ring anchor. Refer to
SB-8, "Removal and Installation"
3. Remove center pillar upper finisher.
a. Apply protective tape (A) to protect the component from damage
as shown.
b. Release center pillar upper finisher cap pawl using a suitable
tool (A) and remove.
: Pawl
c.
Remove the center pillar upper finisher bolt.
JMJIA6495ZZ
JMJIA7787ZZ
JMJIA7788ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст