Nissan Sentra. Instruction — part 846
TM-20
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
SIDE OIL SEAL
REMOVAL AND INSTALLATION
SIDE OIL SEAL
Removal and Installation
INFOID:0000000009759275
REMOVAL
1. Remove front drive shafts. Refer to
FAX-18, "6M/T : Removal and Installation (LH)"
.
2. Remove differential side oil seals (1) from clutch housing and
transaxle case using a suitable tool.
CAUTION:
Do not damage transaxle case and clutch housing.
INSTALLATION
Installation is in the reverse order of removal.
• Install differential side oil seals (1) to clutch housing and transaxle case, using Tools.
CAUTION:
• Do not incline differential side oil seal.
• Do not damage clutch housing and transaxle case.
Inspection
INFOID:0000000009759276
INSPECTION AFTER INSTALLATION
Check the oil level and oil leaks. Refer to
.
SCIA7625E
Tool number
: KV32500QAA
Tool number
: B.vi 1666-B
(A)
: Transaxle case side
(B)
: Clutch housing side
Dimension (L
1
)
: 1.2 – 1.8 mm (0.047 – 0.071 in)
Dimension (L
2
)
: 2.7 – 3.3 mm (0.106 – 0.130 in)
JPDIC0454ZZ
POSITION SWITCH
TM-21
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
POSITION SWITCH
Removal and Installation
INFOID:0000000009759277
REMOVAL
1. Remove battery. Refer to
PG-50, "Removal and Installation (Battery)"
.
2. Disconnect position switch harness connector.
3. Remove position switch from transaxle case.
INSTALLATION
1. Apply recommended sealant to threads of position switch.
• Use Genuine Liquid Gasket, Three Bond 1215 or an equivalent. Refer to
Chemical Products and Sealants"
CAUTION:
Remove old sealant and oil adhering to threads.
2. Install position switch to transaxle case.
3. Tighten position switch to the specified torque. Refer to
4. For the next step and after, install in the reverse order of removal.
Inspection
INFOID:0000000009759278
INSPECTION AFTER INSTALLATION
• Check continuity between position switch terminals. Refer to
TM-17, "BACK-UP LAMP SWITCH : Compo-
(Back-up lamp switch) and
TM-17, "PARK/NEUTRAL POSITION (PNP) SWITCH : Compo-
(PNP switch).
• Check the oil leaks. Refer to
.
TM-22
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
CONTROL LINKAGE
CONTROL LINKAGE
Exploded View
INFOID:0000000009759279
Removal and Installation
INFOID:0000000009759280
REMOVAL
1. Move the shift selector to the neutral position.
2. Remove air cleaner case assembly. Refer to
EM-25, "Removal and Installation"
3. Remove the battery tray and battery support brackets. Refer to
PG-51, "Removal and Installation (Battery
1.
Bracket
2.
Shifter cable
3.
Selector lever
4.
Shift lever
5.
Tapping bolt
6.
M/T cable mounting bracket
7.
Selector cable
8.
Grommet
9.
Shift selector assembly
10.
Shift selector
11.
Shift selector knob
JPDIC0856GB
CONTROL LINKAGE
TM-23
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4. Disconnect the each cable from the shifter lever A (B) and the
selector lever (A) using a suitable tool.
5. While pressing the lock of the selector cable in the direction of
the arrow shown, remove the selector cable from the M/T cable
bracket.
6. While pressing the lock of the shifter cable in the direction of the
arrow shown, remove the shifter cable from the M/T cable
bracket.
7. Remove M/T cable bracket from transaxle case.
8. Remove the center console side finishers (1) (LH/RH).
a. Remove the center console side finisher screw (A) (LH/RH).
b. Release the clips using a suitable tool, then remove the center
console side finisher.
: Metal clip
9. Remove the CVT/MT shift selector finisher (1).
a. Remove cluster lid C. Refer to
IP-20, "Removal and Installation -
.
b. Remove the CVT/MT shift selector screws (A).
c. Release the clips using a suitable tool, then remove the CVT/MT
shift selector finisher.
: Metal clip
10. Pull out and disconnect the shifter cable from the pin of the shift selector assembly using a suitable tool.
ALDIA0380ZZ
JPDIC0793ZZ
ALJIA1037ZZ
ALJIA1038ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст