Nissan Sentra. Instruction — part 266
DLK-180
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK
4. Remove screws and the front door lock assembly.
INSTALLATION
Installation is in the reverse order of removal.
Tighten front door lock screws to specified torque.
CAUTION:
• Do not reuse front door lock assembly screws. Always replace screws with new ones when
removed.
• Check front door lock cables are properly engaged to inside handle and outside handle bracket.
• When installing door key cylinder rod on the (LH) front door, be sure to rotate door key cylinder rod
holder until a click is felt.
• After installation, check front door open/close, lock/unlock operation.
• Check front door lock assembly for poor lubrication. If necessary apply a suitable multi-purpose
grease.
REAR DOOR LOCK
PIIB5812E
Front door lock screws:
5.8 Nm (0.59 kg-m, 51 in-lb)
DOOR LOCK
DLK-181
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK : Exploded View
INFOID:0000000009756492
REAR DOOR LOCK : Removal and Installation
INFOID:0000000009756493
REMOVAL
1. Remove the rear door outside handle. Refer to
DLK-176, "REAR DOOR HANDLE : Removal and Installa-
2. Disconnect the harness connector from the rear door lock actuator.
3. Remove the screws and the rear door lock assembly.
INSTALLATION
Installation is in the reverse order of removal.
Tighten rear door lock screws to specified torque.
1.
Outside handle bracket
2.
Front gasket
3.
Inside handle assembly
4.
Door lock assembly
5.
Outside handle
6.
Outside handle escutcheon
7.
Rear gasket
ALKIA2940ZZ
PIIB5812E
DLK-182
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK
CAUTION:
• Do not reuse rear door lock assembly screws. Always replace screws with new ones when removed.
• Check rear door lock cables are properly engaged to inside handle and outside handle bracket.
• After installation, check rear door open/close, lock/unlock operation.
• Check rear door lock assembly for poor lubrication. If necessary apply a suitable multi-purpose
grease.
Rear door lock screws:
5.8 Nm (0.59 kg-m, 51 in-lb)
TRUNK LID
DLK-183
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID
TRUNK LID ASSEMBLY
TRUNK LID ASSEMBLY : Exploded View
INFOID:0000000009756494
TRUNK LID ASSEMBLY : Removal and Installation
INFOID:0000000009756495
CAUTION:
• Use two people when removing or installing trunk lid assembly due to its heavy weight.
• Use protective tape or shop cloths to protect surrounding components from damage during removal
and installation of trunk lid assembly.
REMOVAL
1. Remove trunk lid finisher (if equipped). Refer to
INT-45, "Removal and Installation"
1.
Trunk lid hinge LH/RH
2.
Torsion bar LH/RH
3.
Torsion bar clips
4.
Trunk lid finisher (if equipped)
5.
Emergency release handle
6.
Emergency release handle clip
7.
Emergency release handle ca-
ble
8.
Trunk lid lock
9.
Trunk lid bumpers
10.
License lamp finisher
11.
Trunk lid
12.
Rear spoiler (if equipped)
13.
Weatherstrip
A.
Clip
Clip
ALKIA2941ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст