Nissan Sentra. Instruction — part 137

BCS-118

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

U1000 CAN COMM

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM

Description

INFOID:0000000009757391

Refer to

LAN-7, "CAN COMMUNICATION SYSTEM : System Description"

.

DTC Logic

INFOID:0000000009757392

DTC DETECTION LOGIC

NOTE:

U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm

that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result

procedure.

Diagnosis Procedure

INFOID:0000000009757393

1.

PERFORM SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON and wait for 2 second or more.

2. Check “SELF- DIAG RESULTS”.
Is “CAN COMM CIRCUIT” displayed?

YES

>> Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation Instruction.

NO

>> Refer to

GI-39, "Intermittent Incident"

.

CONSULT Display

DTC Detection Condition

Possible Cause

CAN COMM CIRCUIT
[U1000]

When any listed module cannot communicate
with CAN communication signal continuously for
2 seconds or more with ignition switch ON

In CAN communication system, any item (or
items) of the following listed below is malfunc-
tioning.
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)

BCS

U1010 CONTROL UNIT (CAN)

BCS-119

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

U1010 CONTROL UNIT (CAN)

DTC Logic

INFOID:0000000009757394

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000009757395

1.

REPLACE BCM

When DTC “U1010” is detected, replace BCM.

>> Replace BCM. Refer to

BCS-126, "Removal and Installation"

.

CONSULT Display

DTC Detection Condition

Possible Cause

CONTROL UNIT (CAN)
[U1010]

BCM detected internal CAN communication cir-
cuit malfunction.

BCM

BCS-120

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000009757396

Regarding Wiring Diagram information, refer to

BCS-111, "Wiring Diagram"

.

1.

CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not blown.

Is the fuse blown?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connectors.

3. Check voltage between BCM connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM connector and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair harness or connector.

Terminal No.

Signal name

Fuses and fusible link No.

63

Battery power supply

12 (10A)

70

G (40A)

11

Ignition switch ACC or ON

18 (10A)

BCM

Ground

Ignition switch position

Connector

Terminal

OFF

ACC

ON

M20

63

Battery voltage

Battery voltage

Battery voltage

70

M21

11

—

0 V

Battery voltage

Battery voltage

BCM

Ground

Continuity

Connector

Terminal

M20

65

—

Yes

BCS

COMBINATION SWITCH INPUT CIRCUIT

BCS-121

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

COMBINATION SWITCH INPUT CIRCUIT

Diagnosis Procedure

INFOID:0000000009757397

Regarding Wiring Diagram information, refer to

BCS-111, "Wiring Diagram"

.

1.

CHECK INPUT 1 - 5 CIRCUIT FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect BCM and combination switch connectors.

3. Check continuity between BCM connector and combination switch connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connectors.

2.

CHECK INPUT 1 - 5 CIRCUIT FOR SHORT

Check for continuity between BCM connector and ground.

Is the inspection result normal?

YES

>> Repair harness or connectors.

NO

>> GO TO 3.

3.

CHECK BCM OUTPUT VOLTAGE

1. Connect BCM connector.

2. Check voltage between BCM connector and ground.

Combination switch

signal

BCM

Combination switch

Continuity

Connector

Terminal

Connector

Terminal

INPUT 1

M21

36

M28

11

Yes

INPUT 2

35

9

INPUT 3

34

7

INPUT 4

33

10

INPUT 5

32

13

Combination switch

signal

BCM

Ground

Continuity

Connector

Terminal

INPUT 1

M21

36

No

INPUT 2

35

INPUT 3

34

INPUT 4

33

INPUT 5

32