Nissan Sentra. Instruction — part 703
SYSTEM
PWC-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
• AUTO UP/DOWN operation can be performed when main power window and door lock/unlock switch turns
to AUTO.
• Encoder continues detecting the movement of power window motor and transmits to main power window
and door lock/unlock switch as the encoder pulse signal while power window motor is operating.
• Main power window and door lock/unlock switch reads the changes of encoder signal and stops AUTO oper-
ation when door glass is at fully opened/closed position.
• Power window motor is operable in case encoder is malfunctioning.
RETAINED POWER OPERATION
• Retained power operation is an additional power supply function that enables power window system to oper-
ate during the 45 seconds even when ignition switch is turned OFF
Retained power function cancel conditions
• Front door CLOSE (door switch OFF)
→OPEN (door switch ON).
• When ignition switch is ON.
• When timer time passes. (45 seconds)
• AUTO function does not operate if encoder is malfunctioning.
POWER WINDOW LOCK FUNCTION
Ground circuit inside main power window and door lock/unlock switch shuts off when power window lock
switch is ON. This inhibits power window switch operation except with the main power window and door lock/
unlock switch.
ANTI-PINCH OPERATION (FRONT LH)
• Pinch foreign material in the door glass during AUTO-UP operation, and it is the anti-pinch function that low-
ers the door glass 150mm. (5.9 in.) or 2 seconds when detected.
• Encoder continues detecting the movement of power window motor and transmits to main power window
and door lock/unlock switch as the encoder pulse signal while power window motor is operating.
• Resistance is applied to the power window motor rotation that changes the frequency of encoder pulse sig-
nal if foreign material is trapped in the door glass.
• Power window switch controls to lower the window glass form 150mm (5.9 in.) or 2 seconds after it detects
encoder pulse signal frequency change.
OPERATION CONDITION
• When door glass AUTO-UP operation is performed (anti-pinch function does not operate just before the door
glass closes and is fully closed)
NOTE:
Depending on environment and driving conditions, if a similar impact or load is applied to the door glass, it
may lower.
Fail-safe
INFOID:0000000009757214
FAIL-SAFE CONTROL
Switches to fail-safe control when malfunction is detected in the encoder signal that detects UP/DOWN speed
and direction of door glass. Switches to fail-safe control when an error beyond the regulation value is detected
between the fully closed position and the actual position of the glass.
Malfunction
Malfunction condition
Pulse sensor malfunction
When only one side of pulse signal is being detected for more than the specified value.
Both pulse sensors mal-
function
When both pulse signals have not been detected for more than the specified value during glass
open/close operation.
Pulse direction malfunc-
tion
When the pulse signal that is detected during glass open/close operation detects the opposite con-
dition of power window motor operating direction.
Glass recognition position
malfunction 1
When it detects the error between glass fully closed position in power window switch memory and
actual fully closed position during glass open/close operation is more than the specified value.
Glass recognition position
malfunction 2
When it detects pulse count more that the value of glass full stroke during glass open/close opera-
tion.
Malfunction of not yet up-
dated closed position of
glass
When glass open/close operation is continuously performed without fully closing more that the spec-
ified value (approximately 10 strokes).
PWC-10
< SYSTEM DESCRIPTION >
SYSTEM
It changes to condition before initialization and the following functions do not operate when switched to fail-
safe control:
• Auto-up operation
• Anti-pinch function
• Retained power function
Perform initial operation to recover when switched to fail-safe mode. However, it switches back to fail-safe
control when malfunction is found in power window switch or in motor.
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
PWC-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010295998
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
Description
ECU identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
ECU id
en
tif
ica
tion
Se
lf Di
ag
no
st
ic
Res
u
lt
Dat
a
M
on
ito
r
Acti
ve
T
est
W
o
rk
su
pp
ort
Co
nf
ig
ur
at
io
n
CAN DIAG SUP
P
OR
T MNTR
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
×
Air conditioner
AIR CONDITIONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
PWC-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
RETAINED PWR
RETAINED PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000010291083
DATA MONITOR
Monitor Item [Unit]
Description
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст