Nissan Sentra. Instruction — part 843
TM-8
< PRECAUTION >
[6MT: RS6F94R]
PRECAUTIONS
Liquid Gasket
INFOID:0000000009759263
REMOVAL OF LIQUID GASKET SEALING
• After removing the bolts and nuts, separate the mating surface and
remove the liquid gasket using Tool (A).
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to
lightly tap (1) the cutter where the liquid gasket is applied. Use a
plastic hammer to slide (2) the cutter by tapping on the side.
CAUTION:
Do not damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using suitable tool (A), remove old liquid gasket adhering to the
liquid gasket application surface and the mating surface.
• Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2. Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3. Attach liquid gasket tube using suitable tool.
Use Genuine Liquid Gasket or equivalent.
4. Apply liquid gasket without gaps to the specified location accord-
ing to the specified dimensions.
• If there is a groove for liquid gasket application, apply liquid
gasket to the groove.
• As for bolt holes (B), normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Check to read the text of this instruction.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this instruction, observe them.
Tool Number (A): KV10111100 (J-37228)
AWBIA1249GB
JPBIA0053ZZ
EMA0622D
(A)
: Groove
: Inside
JPBIA0010ZZ
PREPARATION
TM-9
< PREPARATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009759264
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
KV381054S0
(J-34286)
Puller
Removing mainshaft front bearing outer race
KV38100200
(
—
)
Drift
• Installing mainshaft front bearing outer race
• Installing mainshaft rear bearing outer race
• Installing differential side bearing outer race
(clutch housing side)
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
ST33220000
(
—
)
Drift
Installing input shaft oil seal
a: 37 mm (1.46 in) dia.
b: 31 mm (1.22 in) dia.
c: 22mm (0.87in) dia.
ST33400001
(J-26082)
Drift
Installing differential side bearing outer race
(transaxle case side)
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
KV32500QAA
(
—
)
(Renault SST: B.vi 1666)
Drift set
Installing differential side oil seal
1.
—
(Stamping number: B.vi 1666-A)
Drift
a: 54.3 mm (2.138 in) dia.
b: 45 mm (1.77 in) dia.
c: 26.6 mm (1.047 in) dia.
2.
—
(Stamping number: B.vi 1666-B)
Drift
d: 54 mm (2.13 in) dia.
e: 48.6 mm (1.913 in) dia.
f: 26.6 mm (1.047 in) dia.
ZZA0601D
ZZA1143D
ZZA1046D
ZZA0814D
JPDIC0730ZZ
TM-10
< PREPARATION >
[6MT: RS6F94R]
PREPARATION
ST36720030
(
—
)
Drift
• Installing input shaft rear bearing
• Installing mainshaft front bearing inner race
a: 70 mm (2.76 in) dia.
b: 40 mm (1.57 in) dia.
c: 29 mm (1.14 in) dia.
ST33052000
(
—
)
Drift
• Removing mainshaft rear bearing inner race
• Removing 6th main gear
• Removing 5th main gear
• Removing 4th main gear
• Removing 1st main gear
• Removing 1st-2nd synchronizer hub as-
sembly
• Removing 2nd main gear
• Removing bushing
• Removing 3rd main gear
• Removing mainshaft front bearing inner
race
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
KV32102700
(
—
)
Drift
• Installing bushing
• Installing 2nd main gear
• Installing 3rd main gear
• Installing 4th main gear
• Installing 5th main gear
• Installing 6th main gear
a: 48.6 mm (1.913 in) dia.
b: 41.6 mm (1.638 in) dia.
ST30901000
(J-26010-01)
Drift
Installing mainshaft rear bearing inner race
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.
ST33061000
(J-8107-2)
Drift
Removing differential side bearing inner race
(clutch housing side)
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
KV32300QAM
(
—
)
(Renault SST: B.vi 1823)
Drift
Removing and installing input shaft rear bear-
ing mounting bolt
Tool number
(TechMate No.)
Tool name
Description
ZZA0978D
ZZA0969D
S-NT065
ZZA0978D
ZZA0969D
PCIB2078J
PREPARATION
TM-11
< PREPARATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Commercial Service Tools
INFOID:0000000009759265
Tool name
Description
Socket
Removing and installing drain plug
a: 8 mm (0.31 in)
b: 5 mm (0.20 in)
Spacer
Removing mainshaft front bearing outer race
a: 25 mm (0.98 in) dia.
b: 25 mm (0.98 in)
Drift
Installing bushing
a: 17 mm (0.67 in) dia.
Drift
Removing input shaft rear bearing
a: 24 mm (0.94 in) dia.
Drift
Installing input shaft front bearing
a: 35 mm (1.38 in) dia.
b: 25 mm (0.98 in) dia.
Drift
• Installing input shaft rear bearing
• Removing differential side bearing inner
race (transaxle case side)
a: 43 mm (1.69 in) dia.
PCIB1776E
PCIB1780E
S-NT063
PCIB1779E
S-NT065
NT109
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст