Nissan Sentra. Instruction — part 19
AV-68
< REMOVAL AND INSTALLATION >
[BASE AUDIO]
BLUETOOTH CONTROL UNIT
BLUETOOTH CONTROL UNIT
Removal and Installation
INFOID:0000000009758831
REMOVAL
1. Remove the glove box assembly. Refer to
IP-22, "Removal and Installation"
2. Remove the Bluetooth control unit screws (A) and position aside
the Bluetooth control unit assembly (1).
3. Disconnect the Bluetooth control unit connectors (C) and
release the harness retainer (B) from the Bluetooth control unit
bracket.
4. Release the harness clip (D) from the Bluetooth control unit
bracket and remove the Bluetooth control unit (1).
5. Remove the Bluetooth control unit bracket screws (A), then
remove the Bluetooth control unit (2) from the Bluetooth control
unit bracket (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1417ZZ
ALNIA1418ZZ
AV
MICROPHONE
AV-69
< REMOVAL AND INSTALLATION >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
MICROPHONE
Removal and Installation
INFOID:0000000009758832
REMOVAL
1. Remove the front room/map lamp assembly. Refer to
INL-52, "Removal and Installation"
2. Disconnect the microphone connector (A) from the front room/
map lamp assembly (2).
3. Release the microphone pawls, then remove the microphone
(1).
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1366ZZ
AV-70
< PRECAUTION >
[DISPLAY AUDIO WITHOUT BOSE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010296642
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Trouble Diagnosis
INFOID:0000000009758834
AV COMMUNICATION SYSTEM
• Do not apply voltage of 7.0 V or higher to the measurement terminals.
• Use the tester with its open terminal voltage being 7.0 V or less.
• Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.
Precaution for Harness Repair
INFOID:0000000009758835
AV COMMUNICATION SYSTEM
• Solder the repaired parts, and wrap with tape. [Frays of twisted line
must be within 110 mm (4.33 in).]
PKIA0306E
AV
PRECAUTIONS
AV-71
< PRECAUTION >
[DISPLAY AUDIO WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• Do not perform bypass wire connections for the repair parts. (The
spliced wire will become separated and the characteristics of
twisted line will be lost.)
Precaution for Work
INFOID:0000000009758836
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PKIA0307E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст