Nissan Sentra. Instruction — part 660
PB-6
< BASIC INSPECTION >
PARKING BRAKE SHOE
PARKING BRAKE SHOE
Adjustment - Drum Brake
INFOID:0000000009757406
If equipped with drum brakes, refer to
PB-11, "Inspection and Adjustment"
.
Adjustment - Disc Brake
INFOID:0000000009757407
1. Adjust parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
.
2. Perform parking brake break-in (drag on) operation by driving vehicle under the following conditions:
• Drive forward
• Vehicle speed: Approx. 43 km/h (27 MPH) set (constant and forward)
• Parking brake operating force: 125 N (12.8 kg-f, 28.1 lb-f) set contact
• Time: Approx. 8 sec.
CAUTION:
To prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after
every break-in operation.
3. After the break-in procedure, check parking brake lever stroke.
CAUTION:
If it is out of the specification, adjust again. Refer to
PARKING BRAKE CONTROL
PB-7
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000009757408
Removal and Installation
INFOID:0000000009757409
REMOVAL
Parking Brake Control
1. Remove rear wheels and tires using power tool. Refer to
2. Remove the center console assembly. Refer to
IP-14, "Removal and Installation"
3. Disconnect the parking brake switch harness connector.
4. Remove adjusting nut and loosen front parking brake cable.
5. Remove the parking brake lever assembly.
Rear Parking Brake Cable
1.
Parking brake lever assembly
2.
Adjusting nut
3.
Parking brake switch
4.
Front parking brake cable
5.
Rear parking brake cable (LH)
6.
Rear parking brake cable (RH)
Front
AWFIA0968ZZ
PB-8
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
1. Pull equalizer (A) of the front parking brake cable (1) in a rear-
ward direction and then push upward to remove each rear park-
ing brake cable (2)
2. Remove sub muffler and heat plate. Refer to
EX-5, "Removal and Installation"
.
3. Remove rear parking brake cable from toggle lever. Refer to
(drum brake) or
9, "Exploded View - Disc Brake"
(disc brake).
4. Remove rear parking brake cable bolts.
5. Press the pawl (1) to remove each rear parking brake cable from
the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse adjusting nut.
• Perform adjustment after installation. Refer to
PB-4, "Inspection and Adjustment"
Adjustment
INFOID:0000000009757410
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
JPFIB0129ZZ
JPFIB0130ZZ
PARKING BRAKE SHOE
PB-9
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Removal and Installation - Drum Brake
INFOID:0000000009757411
If equipped with drum brakes, refer to
BR-42, "Removal and Installation"
Exploded View - Disc Brake
INFOID:0000000009757412
Removal and Installation - Disc Brake
INFOID:0000000009757413
REMOVAL
WARNING:
Clean dust on the parking brake shoes with a vacuum dust collector to minimize the hazard of air
borne particles or other materials.
1. Remove rear wheels and tires using power tool. Refer to
2. Remove disc rotor. Refer to
RAX-7, "Removal and Installation - Disc brake"
.
CAUTION:
Parking brake must be completely released before removing rotor.
1.
Anti-rattle pin
2.
Back plate
3.
Toggle lever
4.
Parking brake shoe
5.
Brake strut
6.
Return spring
7.
Spring
8.
Adjuster
Apply PBC (Poly Butyl Cuprysil)
grease or silicone based grease
JPFIB0086ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст