Nissan Sentra. Instruction — part 934
WT-38
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP
Diagnosis
items
Symptom
(Power switch ON)
Low tire pressure warning lamp
Cause
Action
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
illuminates for 1
second, then turns
OFF.
Wake-up operation for
all tire pressure sensors
at wheels is completed.
No system malfunctions
The low tire pres-
sure warning lamp
repeats blinking
ON for 2 seconds
and OFF for 0.2
seconds.
Wake-up operation for
all tire pressure sensors
at wheels is not complet-
ed.
Perform the ID registration
for all tire pressure sensors
at wheels. Refer to
The low tire pres-
sure warning lamp
blinks once.
The front left tire pres-
sure sensor is not acti-
vated.
Perform the ID registration
for the tire pressure sensor
at front left wheel. Refer to
The low tire pres-
sure warning lamp
repeats blinking
twice.
The front right tire pres-
sure sensor is not acti-
vated.
Perform the ID registration
for the tire pressure sensor
at front right wheel. Refer
to
The low tire pres-
sure warning lamp
repeats blinking
for 3 times.
The rear right tire pres-
sure sensor is not acti-
vated.
Perform the ID registration
for the tire pressure sensor
at rear right wheel. Refer to
The low tire pres-
sure warning lamp
repeats blinking
for 4 times.
The rear left tire pres-
sure sensor is not acti-
vated.
Perform the ID registration
for the tire pressure sensor
at rear left wheel. Refer to
The low tire pres-
sure warning lamp
turns ON and
stays illuminated.
Low tire pressure
Check the tire pressure for
all wheels and adjust to the
specified value. Refer to
SEIA0592E
SEIA0593E
JPEIC0090GB
SEIA0595E
SEIA0596E
SEIA0597E
SEIA0598E
LOW TIRE PRESSURE WARNING LAMP
WT-39
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOTE:
If tire pressure sensor wake-up operation is not completed for two or more tire pressure sensors, the applica-
ble low tire pressure warning lamp blinking patterns are displayed continuously.
(Example: Blinks once/OFF/blinks 3 times = Wake-up operation is not completed at the front left wheel and
rear right wheel tire pressure sensors.)
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
repeats blinking at
0.5-second inter-
vals for 1 minute,
and then stays illu-
minated.
The combination meter
fuse is open or removed
(or pulled out).
Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.
The BCM harness con-
nector is removed.
Check the connection con-
ditions of the BCM harness
connector, and repair if
necessary.
Tire Pressure Monitor-
ing System (TPMS) mal-
function.
• Perform CONSULT self-
diagnosis. Refer to
11, "AIR PRESSURE
MONITOR : CONSULT
Function (BCM - AIR
PRESSURE MONI-
TOR)"
(with Intelligent
Key system) or
"AIR PRESSURE MONI-
TOR : CONSULT Func-
tion (BCM - AIR
PRESSURE MONI-
TOR)"
(without Intelligent
Key system).
• If necessary, perform tire
pressure sensor ID reg-
istration. Refer to
.
Diagnosis
items
Symptom
(Power switch ON)
Low tire pressure warning lamp
Cause
Action
SEIA0788E
WT-40
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Low Tire pessure Warning Lamp Does Not Come On When Ignition Switch Is Turned
On
INFOID:0000000009758159
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
DIAGNOSTIC PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform “SELF DIAGNOSTIC RESULT”.
Is DTC “U1000” detected?
YES
>> Malfunction in CAN communication system. Refer to
LAN-16, "Trouble Diagnosis Flow Chart"
NO
>> GO TO 2
2.
CHECK COMBINATION METER
Check combination meter operation. Refer to
MWI-17, "CONSULT Function (METER/M&A)"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Replace combination meter. Refer to
MWI-77, "Removal and Installation"
3.
CHECK LOW TIRE PRESSURE WARNING LAMP
Disconnect BCM harness connector.
Does the low tire pressure warning lamp activate?
YES
>> Replace BCM. Refer to
BCS-73, "Removal and Installation"
(With Intellingent Key System) or
BCS-126, "Removal and Installation"
(Without Intellingent Key System).
NO
>> Check combination meter operation.
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
WT-41
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Low Tire Pressure Warning Lamp Stays On When Ignition Switch Is Turned On
INFOID:0000000009758160
DIAGNOSTIC PROCEDURE
1.
INSPECT BCM CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check terminals for damage or loose connections.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
BCM POWER SUPPLY AND GROUND CIRCUITS
Check BCM power supply and ground circuits. Refer to
WT-34, "WITH INTELLIGENT KEY SYSTEM : Diagno-
(with Intelligent Key system) or
WT-34, "WITHOUT INTELLIGENT KEY SYSTEM : Diagnosis
(without Intelligent Key system).
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-73, "Removal and Installation"
(with Intelligent Key system) or
126, "Removal and Installation"
(without Intelligent Key system).
NO
>> Repair BCM circuits.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст