Nissan Sentra. Instruction — part 119
BCS-46
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM
1
: with CVT
2
: with M/T
Fail-safe
INFOID:0000000009757326
BCM performs fail-safe control when the following DTCs are detected.
100
(R)
Ground
Door switch (AS)
signal
Input
Front door
switch RH
OFF (front RH door
closed)
7.0 - 8.0 V
ON (front RH door open)
0 V
103
(V)
Ground
Trunk room lamp
switch signal
Input
Trunk room
lamp switch
OFF (trunk lid closed)
7.0 - 8.0 V
ON (trunk lid open)
0 V
105
(G)
Ground
Door unlock output
(RR, RL)
Output
Rear doors
UNLOCK (Actuator is acti-
vated)
Battery voltage
Actuator is not activated
0 V
107
(GR)
Ground Trunk open output
Output
Trunk opener
request switch
released
Trunk lid actuator idle
0 V
Trunk opener
request switch
depressed
Trunk lid actuator activat-
ed
Battery voltage
109
(SB)
Ground
Request sw (trunk)
signal
Input
Trunk opener
request switch
Depressed
0 – 1.5 V
Released
Battery voltage
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
−
PKIB4960J
PKIB4960J
CONSULT Display
Fail-safe
Cancellation
B2192: ID DISCORD BCM-ECM
Inhibit engine cranking
Erase DTC
B2193: CHAIN OF BCM-ECM
Inhibit engine cranking
Erase DTC
B2195: ANTI SCANNING
Inhibit engine cranking
Ignition switch ON
→ OFF
B2196: DONGLE NG
Inhibit engine cranking
Erase DTC
B2198: NATS ANTENNA AMP
Inhibit engine cranking
Erase DTC
B2557: VEHICLE SPEED
—
When the following CAN signal status (vehicle speed signal) becomes
consistent
• Vehicle speed signal (ABS)
• Vehicle speed signal (Meter)
B2601: SHIFT P SIGNAL
—
500 ms after the following signal reception status becomes consistent
• Park position switch signal
• P range signal (CAN)
BCS
BCM
BCS-47
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2602: SHIFT P DIAG
—
5 seconds after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
• Park position switch signal: P position (push selector button) or ex-
cept P position (9 – 16 V)
• Vehicle speed: 4 km/h (2.5 MPH) or more
B2603: SHIFT POSITION
—
500 ms after any of the following BCM recognition conditions are fulfilled
• Status 1
- Ignition switch is in the ON position
- Park position switch signal: P position (push selector button) or ex-
cept P position (9 – 16 V)
- P/N position signal: Except P and N positions (0 – 1.5 V)
• Status 2
- Ignition switch is in the ON position
- Park position switch signal: P position (release selector button) (0 –
1.5 V)
- P/N position signal: P or N positions (9 – 16 V)
B2604: SHIFT PN DIAG CAN
—
500 ms after any of the following BCM recognition conditions are fulfilled
• Status 1
- Ignition switch is in the ON position
- P/N position signal: P or N position (9 – 16 V)
- Shift position signal (CAN): P or N position
• Status 2
- Ignition switch is in the ON position
- P/N position signal: Except P and N positions (0 – 1.5 V)
- Shift position signal (CAN): Except P and N position
B2605: SHIFT PN DIAG IPDM
—
500 ms after any of the following BCM recognition conditions are fulfilled
• Status 1
- Ignition switch is in the ON position
- P/N position signal: Except P and N positions (0 – 1.5 V)
• Status 2
- Ignition switch is in the ON position
- P/N position signal: P or N position (9 – 16 V)
B2608: STARTER RELAY
Inhibit engine cranking
500 ms after the following signal communication status becomes con-
sistent
• Starter motor relay control signal
• Starter relay status signal (CAN)
B260F: ECM CAN COMM
Inhibit engine cranking
When any of the following conditions are fulfilled
• Ignition switch changes to ACC
• Receives engine status signal (CAN)
B261F: ASCD CNCL/CLTCH SW
—
BCM detects clutch pedal position switch signal (CAN) status [ON
(Clutch pedal is released)]
B2620: NEUTRAL SW
—
BCM detects neutral switch signal status [OFF (9 – 16 V: Control lever
except NEUTRAL position)]
B26E8: CLUTCH SW
—
When any of the following BCM recognition conditions are fulfilled
• Status 1
- Clutch pedal position switch signal: ON (9 – 16 V: Clutch pedal is re-
leased)
- Clutch interlock switch signal: OFF (0 – 0.5 V: Clutch pedal is re-
leased)
• Status 2
- Clutch pedal position switch signal: OFF (0 – 1.5 V: Clutch pedal is
depressed)
- Clutch interlock switch signal: ON (9 – 16 V: Clutch pedal is de-
pressed)
B26F1: IGN RELAY OFF
Inhibit engine cranking
When the following conditions are fulfilled
• Ignition switch ON signal (CAN: Transmitted from BCM): ON
• Ignition switch ON signal (CAN: Transmitted from IPDM E/R): ON
B26F2: IGN RELAY ON
Inhibit engine cranking
When the following conditions are fulfilled
• Ignition switch ON signal (CAN: Transmitted from BCM): OFF
• Ignition switch ON signal (CAN: Transmitted from IPDM E/R): OFF
CONSULT Display
Fail-safe
Cancellation
BCS-48
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM
DTC Inspection Priority Chart
INFOID:0000000009757327
If more than one DTC is displayed at the same time, perform inspections based on the following priority chart.
B26F3: START CONT RLY ON
Inhibit engine cranking
When the following conditions are fulfilled
• Starter control relay signal (CAN: Transmitted from BCM): OFF
• Starter control relay signal (CAN: Transmitted from IPDM E/R): OFF
B26F4: START CONT RLY OFF
Inhibit engine cranking
When the following conditions are fulfilled
• Starter control relay signal (CAN: Transmitted from BCM): ON
• Starter control relay signal (CAN: Transmitted from IPDM E/R): ON
B26F7: BCM
Inhibit engine cranking
by Intelligent Key sys-
tem
When room antenna and luggage room antenna functions normally
U0415: VDC CAN CIR2
—
When vehicle speed signal (Meter) (CAN) is received normally
CONSULT Display
Fail-safe
Cancellation
Priority
DTC
1
B2562: LOW VOLTAGE
2
• U1000: CAN COMM CIRCUIT
• U1010: CONTROL UNIT (CAN)
3
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2196: DONGLE NG
• B2198: NATS ANTENNA AMP
4
• B2553: IGN POWER CIRCUIT
• B2555: STOP LAMP CIRCUIT
• B2556: ENG START SW
• B2557: VEHICLE SPEED
• B2601: SHIFT P SIGNAL
• B2602: SHIFT P DIAG
• B2603: SHIFT POSITION
• B2604: SHIFT PN DIAG CAN
• B2605: SHIFT PN DIAG IPDM
• B2608: STARTER RELAY
• B260F: ECM CAN COMM
• B2614: ACC RELAY REQ FB
• B2615: IGN RELAY3 REQ FB
• B2616: IGN RELAY2 REQ FB
• B2618: IGN RELAY1 REQ FB
• B261A: ENGINE SW
• B261F: ASCD CNCL/CLTCH SW
• B2620: NEUTRAL SW
• B26E8: CLUTCH SW
• B26F1: IGN RELAY OFF
• B26F2: IGN RELAY ON
• B26F3: START CONT RLY ON
• B26F4: START CONT RLY OFF
• B26F6: BCM
• B26F7: BCM
• B26FC: KEY REGISTRATION
• U0415: VDC CAN CIR2
5
• B2621: INSIDE ANTENNA 1
• B2622: INSIDE ANTENNA 2
• B2623: INSIDE ANTENNA 3
BCS
BCM
BCS-49
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC Index
INFOID:0000000009757328
NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data.
6
• B2626: OUTSIDE 1 ANTENNA
• B2627: OUTSIDE 2 ANTENNA
• B2628: OUTSIDE 3 ANTENNA
7
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESS DATA ERR] FL
• C1717: [PRESS DATA ERR] FR
• C1718: [PRESS DATA ERR] RR
• C1719: [PRESS DATA ERR] RL
• C1729: VHCL SPEED SIG ERR
Priority
DTC
CONSULT display
Fail-safe
Freeze Frame Data
•Vehicle Speed
•Odo/Trip Meter
•Vehicle Condition
Intelligent Key
warning lamp
ON
Low tire
pressure
warning lamp
ON
Reference
page
No DTC is detected.
further testing
may be required.
—
—
—
—
—
U1000: CAN COMM CIRCUIT
—
—
—
—
U1010: CONTROL UNIT (CAN)
—
—
—
—
U0415: VDC CAN CIR2
×
—
×
—
B209F: STR CUT OFF OPEN
×
—
—
—
B20A0: STR CUT OFF SHORT
×
—
—
—
B2192: ID DISCORD BCM-ECM
×
—
—
—
B2193: CHAIN OF BCM-ECM
×
—
—
—
B2195: ANTI SCANNING
×
—
—
—
B2196: DONGLE NG
×
—
—
—
B2198: NATS ANTENNA AMP
×
—
—
—
B2555: STOP LAMP CIRCUIT
—
×
×
—
B2556: ENG START SW
—
×
×
—
B2557: VEHICLE SPEED
×
×
×
—
B2562: LOW VOLTAGE
—
×
—
—
B2601: SHIFT P SIGNAL
×
×
×
—
B2602: SHIFT P DIAG
×
×
×
—
B2603: SHIFT POSITION
×
×
×
—
B2604: SHIFT PN DIAG CAN
×
×
×
—
B2605: SHIFT PN DIAG IPDM
×
×
×
—
B2608: STARTER RELAY
×
×
×
—
B260F: ECM CAN COMM
×
×
×
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст