Nissan Sentra. Instruction — part 491
EXT-32
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
ROOF SIDE MOLDING
Exploded View
INFOID:0000000009758049
Removal and Installation
INFOID:0000000009758050
REMOVAL
ROOF SIDE MOLDING
1. Release roof side molding rear side clip, using a suitable tool
(A).
: Clip
: Front
CAUTION:
Apply protective tape (B) on body to protect the painted
surface from damage.
1. Roof side molding
2. Roof side molding clip
3. Roof panel
4. Body side outer panel
5. Adhesive tape
JMKIB0368ZZ
AWKIA2121ZZ
ROOF SIDE MOLDING
EXT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2. Pull up roof side molding from rear end to front end.
: Front
CAUTION:
Use care when pulling the roof side molding to avoid dam-
aging.
3. Release windshield molding and clip at the front end of roof side
molding, then remove while pulling toward vehicle rear.
: Clip
REMOVAL OF ROOF SIDE MOLDING CLIPS
Heat adhesive tape using a heat gun and peel roof side molding clips (body side) using a suitable tool.
CAUTION:
Be careful not to damage the body.
INSTALLATION
1. Clean tape removed surface with isopropyl alcohol or equivalent.
2. Use two-part epoxy adhesive.
3. Apply adhesive evenly to clip tape surface.
4. Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5. Tape roof side molding clips after press fit and temporarily hold it for specified time based on the following.
CAUTION:
• Use double-sided tape after hardening for roof side molding clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield glass portion, check that body side molding fas-
tener is securely inserted and then press in.
• Do not wash the vehicle within 24 hours so as to keep adhesive dry.
JMKIA3884ZZ
AWKIA2122ZZ
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
× 2 seconds
5 to 10
°C (41 to 50°F)
: 1 hour or more
11 to 23
°C (52 to 73°F)
: 30 minutes or more
24
°C or more (75°F or more)
: 15 minutes or more
EXT-34
< REMOVAL AND INSTALLATION >
DRIP MOLDING
DRIP MOLDING
Exploded View
INFOID:0000000009758051
Removal and Installation
INFOID:0000000009758052
REMOVAL
Release drip molding clips, then remove drip molding.
INSTALLATION
Installation is in the reverse order of removal.
1.
Drip molding
Clip
AWKIA2123ZZ
DOOR SASH TAPE
EXT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
DOOR SASH TAPE
Exploded View
INFOID:0000000009758053
FRONT DOOR SASH TAPE
FRONT DOOR SASH TAPE : Removal and Installation
INFOID:0000000009758054
REMOVAL
Heat door sash tape surface using a heat gun and peel door sash tape.
CAUTION:
Do not damage painted surface of door.
INSTALLATION
NOTE:
For installation position of door sash tape, refer to the position as shown.
1.
Front door sash upper tape
2.
Front door assembly
3.
Rear door assembly
4.
Front door sash rear tape
5.
Rear door sash front tape
6.
Rear door sash rear tape
7.
Rear door sash upper tape
JMKIB0370ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст