Nissan Quest E52. Instruction — part 128
AV
STEERING SWITCH SIGNAL B CIRCUIT
AV-391
< DTC/CIRCUIT DIAGNOSIS >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Standard
Between terminals 14 and 17
switch
ON
: 708 – 737
Ω
MENU DOWN switch ON
: 314 – 327
Ω
MENU UP switch ON
: 118 – 123
Ω
SOURCE switch ON
: Less than 1
Ω
Between terminals 15 and 17
switch ON
: 314 – 327
Ω
VOL UP switch ON
: 118 – 123
Ω
VOL DOWN switch ON
: Less than 1
Ω
JSNIA0216GB
AV-392
< DTC/CIRCUIT DIAGNOSIS >
[BOSE AUDIO WITHOUT NAVIGATION]
STEERING SWITCH GROUND CIRCUIT
STEERING SWITCH GROUND CIRCUIT
Description
INFOID:0000000009652210
Transmits the steering switch signal to AV control unit.
Diagnosis Procedure
INFOID:0000000009652211
1.
CHECK STEERING SWITCH SIGNAL GROUND CIRCUIT
1.
Disconnect AV control unit connector and spiral cable connector.
2.
Check continuity between AV control unit harness connector and spiral cable harness connector.
3.
Connect AV control unit connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK SPIRAL CABLE
Check spiral cable.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace spiral cable. Refer to
SR-15, "Removal and Installation"
3.
CHECK GROUND CIRCUIT
1.
Connect AV control unit connector.
2.
Check continuity between AV control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace AV control unit. Refer to
AV-404, "Removal and Installation"
.
4.
CHECK STEERING SWITCH
1.
Turn ignition switch OFF.
2.
Check steering switch. Refer to
AV-392, "Component Inspection"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace steering wheel. Refer to
ST-12, "Removal and Installation"
Component Inspection
INFOID:0000000009652212
Measure the resistance between the steering switch connector terminals 14 to 17 and 15 to 17.
AV control unit
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M171
15
M33
33
Existed
AV control unit
Ground
Continuity
Connector
Terminal
M171
15
Existed
AV
STEERING SWITCH GROUND CIRCUIT
AV-393
< DTC/CIRCUIT DIAGNOSIS >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Standard
Between terminals 14 and 17
switch
ON
: 708 – 737
Ω
MENU DOWN switch ON
: 314 – 327
Ω
MENU UP switch ON
: 118 – 123
Ω
SOURCE switch ON
: Less than 1
Ω
Between terminals 15 and 17
switch ON
: 314 – 327
Ω
VOL UP switch ON
: 118 – 123
Ω
VOL DOWN switch ON
: Less than 1
Ω
JSNIA0216GB
AV-394
< SYMPTOM DIAGNOSIS >
[BOSE AUDIO WITHOUT NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009652213
OPERATION
RELATED TO HANDS-FREE PHONE
• Before performing diagnosis, confirm that the cellular phone being used by the customer is compatible with
the vehicle.
• It is possible that a malfunction is occurring due to a version change of the phone even though the phone is
a compatible type. This can be confirmed by changing the cellular phone to another compatible type, and
checking that it operates normally. It is important to determine whether the cause of the malfunction is the
vehicle or the cellular phone.
Check Compatibility
1.
Make sure the customer's Bluetooth
®
related concern is understood.
2.
Verify the customer's concern.
NOTE:
The customer's phone may be required, depending upon their concern.
3.
Write down the customer's phone brand, model, and service provider.
NOTE:
It is necessary to know the service provider. On occasion, a given phone may be on the approved list with
one provider, but may not be on the approved list with other providers.
4.
Go to “www.nissanusa.com/bluetooth/”.
a.
Using the website's search engine, find out if the customer's phone is on the approved list.
b.
If the customer's phone is NOT on the approved list:
Stop diagnosis here. The customer needs to obtain a Bluetooth
®
phone that is on the approved list before
any further action.
c.
If the feature related to the customer's concern shows as “N” (not compatible):
Stop diagnosis here. If the customer still wants the feature to function, they will need to get an approved
phone showing the feature as “Y” (compatible) in the “Basic Features” list.
d.
If the feature related to the customer's concern shows as “Y” (compatible):
Perform diagnosis as per the following table.
Symptoms
Check items
Probable malfunction location
Multifunction switch and preset
switch operation does not work.
• All switches cannot be operated.
• “MULTI AV” is displayed on system
selection screen when the CONSULT
is started.
• Multifunction switch power supply and ground circuit.
• AV communication circuit between AV control unit and
multifunction switch.
Perform CONSULT self-diagnosis.
Refer to
.
• All switches cannot be operated.
• “MULTI AV” is not displayed on sys-
tem selection screen when the CON-
SULT is initialized.
AV control unit power supply and ground circuit malfunc-
tion. Refer to
AV-367, "AV CONTROL UNIT : Diagnosis
.
Only specified switch cannot be operat-
ed.
Multifunction switch or preset switch malfunction.
Perform multifunction switch and preset switch self-di-
agnosis function. Refer to
.
Fuel economy display is abnor-
mal.
There is malfunction in the CONSULT
“self-diagnosis result” of “MULTI AV”.
Refer to
Perform detected DTC diagnosis.
Refer to
.
There is no malfunction in the CON-
SULT “self-diagnosis result” of “MULTI
AV”.
Refer to
Ignition signal circuit malfunction. (AV control unit)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст