Nissan Quest E52. Instruction — part 1279
FRONT WIPER DOES NOT OPERATE
WW-49
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NO
>> Repair or replace the applicable parts.
WW-50
< REMOVAL AND INSTALLATION >
FRONT WIPER
REMOVAL AND INSTALLATION
FRONT WIPER
Exploded View
INFOID:0000000009649569
REMOVAL VIEW
DISASSEMBLY VIEW
1.
Front wiper arm cap
2.
Front wiper arm LH
3.
Front wiper blade LH
4.
Front wiper refill LH
5.
Front wiper arm RH
6.
Front wiper blade RH
7.
Front wiper refill RH
8.
Front wiper drive assembly
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA2122GB
FRONT WIPER
WW-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER ARM
WIPER ARM : Removal and Installation
INFOID:0000000009649570
REMOVAL
1.
Operate front wiper to move it to the auto stop position.
2.
Fully open hood assembly.
3.
Pull front wiper arm caps in direction indicated by arrow as
shown in the figure. Remove front wiper arm caps.
4.
Remove front wiper arm mounting nuts.
5.
Raise front wiper arm, and remove front wiper arm from the front wiper drive assembly.
INSTALLATION
1.
Clean front wiper arm mount as shown in the figure to prevent
nuts from being loosened.
JMLIA2064ZZ
1.
Wiper linkage 2
2.
Wiper linkage 1
3.
Shaft seal
4.
Motor arm
5.
Front wiper motor assembly
6.
Front wiper frame
: Multi-purpose grease or an equivalent
: Pawl
JMLIA2157ZZ
ELH0717D
WW-52
< REMOVAL AND INSTALLATION >
FRONT WIPER
2.
Operate front wiper motor to move the wiper to the auto stop position.
3.
Install front wiper arm to front wiper drive assembly. Temporarily tighten mounting nut.
4.
Adjust front wiper blade position. Refer to
WW-52, "WIPER ARM : Adjustment"
5.
Install front wiper arms by tightening the mounting nuts.
For the specified torque, refer to
.
6.
Operation wiper to move it to the auto stop position.
CAUTION:
Before operating wiper, inject washer fluid so that windshield glass damage by wiper operation is
prevented.
7.
Check that front wiper blades stop at the specified position.
8.
Install front wiper arm caps.
WIPER ARM : Adjustment
INFOID:0000000009649571
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover/ front fender cover and the top of front wiper blade center.
Standard clearance
WIPER BLADE
WIPER BLADE : Removal and Installation
INFOID:0000000009649572
REMOVAL
1.
Lift up front wiper arm, and set to the position where wiper arm can be locked back.
1.
Windshield glass
2.
Front fender cover
3.
Front wiper blade RH
4.
Cowl top cover
5.
Front wiper blade LH
JMLIA2124ZZ
D
: 35.0
±
7.5 mm (1.378
±
0.295 in)
P
: 37.2
±
7.5 mm (0.295
±
0.295 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст