Nissan Quest E52. Instruction — part 575
FUEL INJECTOR AND FUEL TUBE
EM-49
< REMOVAL AND INSTALLATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
8.
Loosen mounting bolts in the reverse order as shown in the fig-
ure, and remove fuel tube and fuel injector assembly.
CAUTION:
Never tilt fuel tube, or remaining fuel in pipes may flow out
from pipes.
9.
Remove fuel injector from fuel tube as follows:
a.
Open and remove clip (1).
b.
Remove fuel injector (2) from fuel tube (5) by pulling straight.
CAUTION:
• Be careful with remaining fuel that may go out from fuel
tube.
• Be careful not to damage injector nozzle during removal.
• Never bump or drop fuel injector.
• Never disassemble fuel injector.
10. Remove fuel damper from fuel tube.
INSTALLATION
CAUTION:
Do not reuse O-rings.
1.
Install fuel damper as follows:
a.
Install new O-ring (2) to fuel tube (1) as shown. When handling
new O-ring, be careful of the following caution:
CAUTION:
• Do not reuse O-rings.
• Handle O-ring with bare hands. Never wear gloves.
• Lubricate O-ring with new engine oil.
• Never clean O-ring with solvent.
• Check that O-ring and its mating part are free of foreign
material.
• When installing O-ring, be careful not to scratch it with
tool or fingernails. Also be careful not to twist or stretch
O-ring. If O-ring was stretched while it was being
attached, never insert it quickly into fuel tube.
• Insert new O-ring straight into fuel tube. Never twist it.
b.
Install spacer (3) to fuel damper (4).
c.
Insert fuel damper straight into fuel tube.
CAUTION:
• Insert straight, checking that the axis is lined up.
• Never pressure-fit with excessive force.
• Insert fuel damper until (B) is touching (A) of fuel tube.
d.
Tighten bolts evenly in turn.
• After tightening bolts, check that there is no gap between fuel damper cap (5) and fuel tube.
2.
Install new O-rings to fuel injector paying attention to the following.
: Engine front
JPBIA1715ZZ
3
: O-ring (green)
4
: O-ring (black)
A
: Installed condition
B
: Clip mounting groove
JPBIA1958ZZ
Reference value
: 130 N (13.3 kg, 29.2 lb)
JPBIA0316ZZ
EM-50
< REMOVAL AND INSTALLATION >
[VQ35DE]
FUEL INJECTOR AND FUEL TUBE
CAUTION:
• Do not reuse O-rings.
• Upper and lower O-ring are different. Be careful not to confuse them.
• Handle O-ring with bare hands. Never wear gloves.
• Lubricate O-ring with new engine oil.
• Never clean O-ring with solvent.
• Check that O-ring and its mating part are free of foreign material.
• When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to
twist or stretch O-ring. If O-ring was stretched while it was being attached, never insert it quickly
into fuel tube.
• Insert O-ring straight into fuel injector. Never decenter or twist it.
3.
Install fuel injector to fuel tube as follows:
a.
Insert clip (3) into clip mounting groove (F) on fuel injector (5).
• Insert clip so that protrusion (E) of fuel injector matches cutout
(C) of clip.
CAUTION:
• Never reuse clip. Replace it with new one.
• Be careful to keep clip from interfering with O-ring. If
interference occurs, replace O-ring.
b.
Insert fuel injector into fuel tube (1) with clip attached.
• Insert it while matching it to the axial center.
• Insert fuel injector so that protrusion (A) of fuel tube matches
cutout (B) of clip.
• Check that fuel tube flange (G) is securely fixed in flange fixing
groove (D) on clip.
c.
Check that installation is complete by checking that fuel injector
does not rotate or come off.
• Check that protrusions of fuel injectors and fuel tubes are
aligned with cutouts of clips after installation.
4.
Install fuel tube and fuel injector assembly to intake manifold.
CAUTION:
Be careful not to let tip of injector nozzle come in contact with other parts.
• Tighten mounting bolts in two steps in numerical order as
shown in the figure.
5.
Connect fuel injector harness.
6.
Install intake manifold collector. Refer to
.
7.
Connect quick connector between fuel feed hose and fuel tube connection with the following procedure:
Fuel tube side
: Black
Nozzle side
: Green
2
: O-ring (black)
4
: O-ring (green)
JPBIA1959ZZ
: Engine front
1st step
: 10.1 N·m (1.0 kg-m, 7 ft-lb)
2nd step
: 22.0 N·m (2.2 kg-m, 16 ft-lb)
JPBIA1715ZZ
FUEL INJECTOR AND FUEL TUBE
EM-51
< REMOVAL AND INSTALLATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Check no foreign substances are deposited in and around fuel tube and quick connector, and no damage
on them.
b.
Thinly apply new engine oil around fuel tube from tip end to spool end.
c.
Align center to insert quick connector straightly into fuel tube.
• Insert quick connector (1) to fuel tube until top spool (2) is
completely inside quick connector, and 2nd level spool (3)
exposes right below quick connector.
CAUTION:
• Hold (A) position as shown in the figure when inserting
fuel tube into quick connector.
• Carefully align center to avoid inclined insertion to pre-
vent damage to O-ring inside quick connector.
• Insert until you hear a “click” sound and actually feel the engagement.
• To avoid misidentification of engagement with a similar sound, be sure to perform the next step.
d.
Pull quick connector by hand holding position. Check it is completely engaged (connected) so that it does
not come out from fuel tube.
e.
Install quick connector cap (3) to quick connector.
• Install quick connector cap with arrow (A) on surface facing in
direction of quick connector (fuel feed hose side).
CAUTION:
If quick connector cap cannot be installed smoothly, quick
connector may have not been installed correctly. Check
connection again.
f.
Secure fuel feed hose to clamp of quick connector cap.
8.
Install in the reverse order of removal after this step.
Inspection
INFOID:0000000009652779
INSPECTION AFTER INSTALLATION
Check on Fuel Leakage
1.
Turn ignition switch “ON” (with the engine stopped). With fuel pressure applied to fuel piping, check there
are no fuel leakage at connection points.
NOTE:
Use mirrors for checking at points out of clear sight.
2.
Start the engine. With engine speed increased, check again that there are no fuel leakage at connection
points.
CAUTION:
Never touch the engine immediately after stopped, as the engine becomes extremely hot.
B
: Fitted condition
: Upright insertion
1
: Fuel feed hose
2
: Fuel tube
B
: Upper view
JPBIA0275ZZ
JPBIA0039ZZ
EM-52
< REMOVAL AND INSTALLATION >
[VQ35DE]
IGNITION COIL, SPARK PLUG AND ROCKER COVER
IGNITION COIL, SPARK PLUG AND ROCKER COVER
Exploded View
INFOID:0000000009652780
Removal and Installation
INFOID:0000000009652781
REMOVAL
1.
Remove the following parts:
1.
Ignition coil
2.
Spark plug
3.
PCV hose
4.
Clamp
5.
PCV valve
6.
O-ring
7.
Rocker cover (bank 1)
8.
PCV hose
9.
Rocker cover gasket (bank 1)
10.
O-ring
11.
Camshaft position sensor (PHASE)
(bank 1)
12. Oil filler cap
13.
Rocker cover (bank 2)
14.
Rocker cover gasket (bank 2)
15.
Camshaft position sensor (PHASE)
(bank 2)
16.
PCV hose
17.
Clamp
A.
To intake manifold collector
B.
Comply with the assembly procedure
when tightening. Refer to
C.
Camshaft bracket side
D.
To air duct assembly
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Should be lubricated with oil.
: Sealing point
JPBIA1637GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст