Nissan Quest E52. Instruction — part 321
DEF-38
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER INDICATOR DOES NOT ILLUMINATE
REAR WINDOW DEFOGGER INDICATOR DOES NOT ILLUMINATE
Diagnosis Procedure
INFOID:0000000009650851
1.
CHECK REAR WINDOW DEFOGGER FEEDBACK SIGNAL
Check rear window defogger feedback signal.
Refer to
DEF-30, "WITH AUTO A/C : Component Function Check"
(With auto A/C) or
UAL A/C : Component Function Check"
(With instruction A/C).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
FILAMENT
DEF-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
REMOVAL AND INSTALLATION
FILAMENT
Inspection and Repair
INFOID:0000000009650852
INSPECTION
1.
When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
2.
Attach probe circuit tester (in Volt range) to middle portion of
each filament.
3.
If a filament is burned out, circuit tester registers 0 or battery
voltage.
4.
To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)
SEL122R
SEL263
SEL265
DEF-40
< REMOVAL AND INSTALLATION >
FILAMENT
• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth
REPAIRING PROCEDURE
1.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4.
After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5.
Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D
DLK-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
DLK
A
B
DLK
N
O
P
CONTENTS
DOOR & LOCK
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . ..
Precaution for Procedure without Cowl Top Cover
Precautions For Xenon Headlamp Service . . . .
Precautions for Removing Battery Terminal . . ...
Work . . . . . . . . . . . . . . . . . .
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . ..
Special Service Tools . . . . . . . . . . . ..
Commercial Service Tools . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . .
COMPONENT PARTS . . . . . . . . . ...
DOOR LOCK SYSTEM . . . . . . . . . . . .
DOOR LOCK SYSTEM : Component Parts Loca-
tion . . . . . . . . . . . . . . . . . . ..
AUTOMATIC BACK DOOR SYSTEM . . . . . ...
AUTOMATIC BACK DOOR SYSTEM :
Component Parts Location . . . . . . . . .
AUTOMATIC SLIDING DOOR SYSTEM . . . . ...
AUTOMATIC SLIDING DOOR SYSTEM : Com-
ponent Parts Location . . . . . . . . . . . .
Inside Key Antenna . . . . . . . . . . . . .
Front Door Outside Handle Assembly (Outside
Key Antenna) . . . . . . . . . . . . . . ..
Outside Key Antenna (Rear Bumper) . . . . . .
Remote Keyless Entry Receiver . . . . . . . .
Intelligent Key Warning Buzzer . . . . . . . ...
Door Lock and Unlock Switch (Driver Side) . . .
Door Lock and Unlock Switch (Passenger Side) ....
Front Door Request Switch . . . . . . . . . .
Front Door Switch . . . . . . . . . . . . ...
Front Door Lock Assembly (Driver Side) . . . . .
Back Door Opener Switch . . . . . . . . . ...
Back Door Request Switch . . . . . . . . . ..
Back Door Lock Assembly (Without Automatic
Back Door System) . . . . . . . . . . . . ..
Back Door Control Unit (Without Automatic Back
Door System) . . . . . . . . . . . . . . ...
Selective Unlock Relay . . . . . . . . . . .
Back Door Touch Sensor . . . . . . . . . .
Automatic Back Door Control Module . . . . . .
Automatic Back Door Switch . . . . . . . . ...
Automatic Door Main Switch . . . . . . . . ...
Automatic Back Door Warning Buzzer . . . . .
Automatic Back Door Close Switch . . . . . . .
Back Door Lock Assembly (With Automatic Back
Door System) . . . . . . . . . . . . . . ...
Automatic Back Door Opener Switch . . . . . ..
Automatic Sliding Door Open/Close Switch . . .
Automatic Sliding Door Unit . . . . . . . . . .
Sliding Door Control Unit . . . . . . . . . . .
Automatic Sliding Door Warning Buzzer . . . . .
Automatic Sliding Door One-Touch Open/Close
Switch . . . . . . . . . . . . . . . . . ..
Remote Control Assembly . . . . . . . . . ...
Sliding Door Switch . . . . . . . . . . . . .
Sliding Door Lock Actuator . . . . . . . . . ..
Sliding Door Lock Release Actuator . . . . . .
Sliding Door Lock Assembly . . . . . . . . .
Sliding Door Touch Sensor . . . . . . . . . ..
Fuel Filler Lid Sliding Door Unit . . . . . . . ...
SYSTEM (POWER DOOR LOCK SYSTEM) .
System Description . . . . . . . . . . . . ..
Circuit Diagram . . . . . . . . . . . . . .
SYSTEM (INTELLIGENT KEY SYSTEM) . . .
INTELLIGENT KEY SYSTEM . . . . . . . . .
INTELLIGENT KEY SYSTEM : System Descrip-
tion . . . . . . . . . . . . . . . . . . ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст