Nissan Quest E52. Instruction — part 995
PWC-92
< BASIC INSPECTION >
[DRIVER SIDE WINDOW ANTI-PINCH]
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL
Description
INFOID:0000000009653361
When the battery negative terminal is disconnected, the initialization is necessary for normal operation of
power window system.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000009653362
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
>> END
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW MAIN SWITCH
PWC-93
< BASIC INSPECTION >
[DRIVER SIDE WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW MAIN
SWITCH
Description
INFOID:0000000009653363
When the power window main switch replaced, the initialization in necessary for normal operation of power
window system.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000009653364
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
>> END
PWC-94
< BASIC INSPECTION >
[DRIVER SIDE WINDOW ANTI-PINCH]
SYSTEM INITIALIZATION
SYSTEM INITIALIZATION
Description
INFOID:0000000009653365
If any of the following operations are performed, the initialization is necessary for normal operation of power
window system.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000009653366
1.
STEP 1
1.
Turn ignition switch ON.
2.
Operate power window switch to fully open the window. (This operation is unnecessary if the window is
already fully open)
3.
Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed
position, keep pulling the switch for 2 seconds or more.
4.
Check that AUTO-UP function operates normally.
>> GO TO 2.
2.
STEP 2
Check anti-pinch function. Refer to
>> END
CHECK ANTI-PINCH FUNCTION
PWC-95
< BASIC INSPECTION >
[DRIVER SIDE WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
CHECK ANTI-PINCH FUNCTION
Description
INFOID:0000000009653367
If any of the following operations are performed, the initialization is necessary for normal operation of anti-
pinch function.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
Work Procedure
INFOID:0000000009653368
1.
CHECK ANTI-PINCH FUNCTION
1.
Fully open the door window.
2.
Place a piece of wood near fully closed position.
3.
Close door glass completely with AUTO-UP.
4.
Check the following conditions.
-
Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.
-
Check that glass does not rise not when operating the power window main switch while lowering.
CAUTION:
•
Perform initial setting when AUTO-UP operation or anti-pinch function does not operate nor-
mally.
•
Check that AUTO-UP operates before inspection when system initialization is performed.
•
Do not check with hands and other body parts because they may be pinched. Do not get
pinched.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст