Nissan Quest E52. Instruction — part 260
BRM-6
< PREPARATION >
REPAIRING MATERIAL
PREPARATION
REPAIRING MATERIAL
Foam Repair
INFOID:0000000009648862
During factory body assembly, foam insulators are installed in certain body panels and locations around the
vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.
URETHANE FOAM APPLICATIONS
Use commercially available Urethane foam for sealant (foam material) repair of material used on vehicle.
Read instructions on product for fill procedures.
Example of foaming agent filling operation procedure
1.
Fill procedures after installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating form insulator and foam material.
c.
Install service part.
d.
Insert nozzle into hole near fill area and fill foam material or fill enough to close gap with the service part.
2.
Fill procedures before installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating foam insulator and foam material.
c.
Fill foam material on wheelhouse outer side.
<Urethane foam for foaming agent>
3M™ Automix™ Flexible Foam 08463 or equiva-
lent
1.
Urethane foam
A.
Nozzle insert hole
: Vehicle front
JSKIA0129GB
REPAIRING MATERIAL
BRM-7
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
NOTE:
Fill enough to close gap with service part while avoiding flange
area.
d.
Install service part.
NOTE:
Refer to label for information on working times.
1.
Urethane foam
A.
Fill while avoiding flange area
: Vehicle front
JSKIA0130GB
BRM-8
< PREPARATION >
BODY COMPONENT PARTS
BODY COMPONENT PARTS
Underbody Component Parts
INFOID:0000000009648863
: Both sided anti-corrosive precoated steel sections
: High strength steel (HSS) sections
: Both sided anti-corrosive steel and HSS sections
JSKIA2474ZZ
BODY COMPONENT PARTS
BRM-9
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
No.
Parts name
Tensile strength
(MPa)
Both sided
anti-corrosive
precoated
steel sections
1.
Rear floor rear
Under 440
×
2.
Jack mounting bracket
Under 440
—
3.
Rear floor rear side (RH & LH)
590
×
4.
Woofer bracket assembly
Under 440
—
5.
Rear floor extension front (RH & LH)
590
×
6.
Inner sill step extension assembly (RH & LH)
Under 440
×
7.
Rear floor side reinforcement
Under 440
—
8.
Rear floor front
Under 440
×
9.
Spare tire mounting bracket (Right)
Under 440
×
10.
Spare tire mounting bracket (Center)
Under 440
×
11.
Parking brake reinforcement
Under 440
×
12.
Front floor
a.
T=2.0mm
(0.079 in)
1350 MPa
caution
780
×
13.
Inner sill (RH & LH)
b.
T=1.4mm
(0.055 in)
980 MPa
caution
590
×
14.
Center cowl top
Under 440
×
15.
Side dash (RH & LH)
Under 440
×
16.
Upper dash
Under 440
×
17.
Lower dash
590
×
18.
Hoodledge assembly (RH & LH)
Refer to No.19–20
19.
Upper hoodledge (RH & LH)
Under 440
×
20.
Lower rear hoodledge (RH & LH)
440
×
21.
Hoodledge reinforcement (RH & LH)
Under 440
×
22.
Upper radiator core support (RH & LH)
Under 440
×
23.
Front side member closing plate assembly (RH & LH)
780
×
24.
Lower front hoodledge (RH & LH)
Under 440
×
25.
Front side member assembly (RH & LH)
c.
T=2.0mm
(0.079 in)
980 MPa
caution
780
×
26.
Side radiator core support (RH & LH)
Under 440
×
27.
Front side member connector assembly (RH & LH)
Under 440
—
28.
Front side member extension front (RH & LH)
780
×
29.
Front side member extension center (RH & LH)
780
×
30.
Rear floor front stiffener
780
×
31.
Front side member extension rear (RH & LH)
780
×
32.
Rear sill assembly (RH & LH)
590
×
33.
3rd crossmember
590
×
34.
4th crossmember
440
×
35.
5th crossmember
590
×
36.
6th crossmember
590
×
37.
7th crossmember
590
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст